Kenwood LSF-1010 Clip-on Mount

21

LSF-1010 (EN)

DEUTSCH

FRANÇAIS ESPAÑOL

NEDERLANDS ITALIANO

Clip-on Mount

Use the following procedure to clip the speaker onto an object other than the

base. You can clip to either a cylindrical fixture (such as a thin pipe) or a flat-edge

fixture (such as the edge of a bookshelf).

Conditions

If flat: Width should be 12 to 15 mm (about 0.5 to 0. 6 inches)

If cylindrical: Diameter should be 12 to 20 mm (about 0.5 to 0.8 inches).

Other Ways to Set Up the Satellite Speakers

For information about how to remove/replace the screw caps and loosen the arm

screws, see page 16, “Getting Ready to Adjust.”

1. Remove the arm.

1Loosen the two arm screws and pull

the arm out.

• Unplug the cord from the jack before

removing the arm.

• If you want to change the angle of the

arm, set the arm holders to the appro-

priate angle. For instructions, see

page 17, “Adjusting the Arm Angle.”

2. Clamp the clip onto an appropriate object.

1Unclamp the clip from the stand, and

clamp it onto an appropriate flat edge

or cylinder.

• If clipping to a flat edge, set so that the

entire rubber part of the clip makes

contact with the flat surface.

• If clipping to a cylinder, set so that the

rubber part fits (curves) around the

cylinder.

2Gently push the clip up, down, right,

and left to confirm that it is securely

fixed in place and maintains its posi-

tion. Many objects are not suitable as

supports — either because the mate-

rial is not strong enough or because

the surface does not allow an adequate

grip. Do not clip to any object that does

not offer sufficient stability.

(To be continued.)

Loosen the screws.

Contents

Main Before applying power Caution : Read this section carefully to ensure safe operation. Introduction Safety precautions Caution : Read this section carefully to ensure safe operation. WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Unpacking Introduction Contents IMPORTANT SAFEGUARDS Caution : Read this page carefully to ensure safe operation. IMPORTANT SAFEGUARDS Location and Orientation Attaching the Cushions Satellite Speakers Subwoofer Location and Orientation Location Precautions Interference with AM Reception Subwoofer and Satellite Speaker Magnetic Shielding and TV Color Reception Feedback (Howling) CAUTION (SUBWOOFER only) Setting Up the Satellite Speakers 1. Attach the speaker to the arm. FIRST: Attach speaker cord. Adjusting the Speaker Angle 2. Attach the arm to the stand. Setting Up the Satellite Speakers Before Connecting... Making Connections Subwoofer 1. If your amp or receiver includes a SUBWOOFER PRE- OUT jack: 2. If your amp or receiver does not include a SUBWOOFER PRE-OUT jack: 3. If your amp or receiver includes standard PRE-OUT jacks: Connecting to Amp's SUBWOOFER PRE-OUT Jack Do not plug in the power cord until you have finished mak- ing all connections. Connecting to Amp's Speaker Output Terminals IMPORTANT Connecting to Amp's Standard PRE-OUT Jacks Note About Pin-Plug Cables Components and Their Functions Subwoofer Adjusting the Sound 1. Adjusting the Volume 2. Adjusting the Turnover Frequency Important Operating Notes Satellite Speakers Subwoofer Getting Ready to Adjust 1. Remove the screw cap covering each arm screw. Adjusting the Satellite Speaker Position 2. Loosen the two screws. Adjusting the Arm Height 3. Replace the screw caps. Adjusting the Satellite Speaker Position Adjusting the Arm Angle 2. Set the arm holders to the desired angle. 3. Insert and fasten the arm. Offset Mount Other Ways to Set Up the Satellite Speakers 2. Set the arm holder to vertical position. 3. Attach and fasten the arm. Wall Mount 2. Set the arm holders to the desired angle. 3. Attach speaker cord to the base. 4. Reattach the clip to the pole. 5. Attach and fasten the arm. 6. Mount the stand onto the wall. Clip-on Mount 2. Clamp the clip onto an appropriate object. 3. Attach and fasten the arm. Maintenance Cleaning Contact Restorers 2- 1- Troubleshooting Specifications Subwoofer Satellite speaker