From your usual listening position, adjust the volume levels. The volume levels from each speaker should be the same.
If the input level of an analog source signal is too high, the CLIP indicator 21 will blink. Adjust the input level.
1Use the MULTI CONTROL knob or 5/∞ keys to adjust the volume of the test tone output from the speaker channel to be adjusted.
The channel indication blinks while the test tone is being output.
SP | A | TI.VOL | L | C | R | FM | DIGITAL | |
|
| MUTE | LFE |
|
| AM PRO LOGIC S.DIRECT | ||
RDS | EON | PTY |
|
| MHz 3 STEREO MONITOR | |||
LS | S | RS | kHz DOWN MIX | DSP | ||||
TP | TA | NEWS | ||||||
|
|
|
|
| ||||
The test tone is heard from the speakers in the following sequence for 2 seconds each:
= L = C = R = SR = SL = SW
•If you change the volume level settings for the speakers while listening to music, the settings referred to on this page are also
changed | º |
•If the speaker setting selects are OFF, the speaker level settings are reset.
2Press the SET UP or display operation 2 [Next] key.
•The test tone is turned off. The receiver enters the mode for inputting the distance to the speakers.
4Input the distance to the speakers. |
CLIP
1Use the INPUT SELECTOR knob to select the source which input level you want to adjust.
• You can store a separate input level for each input source. If the MONITOR function is ON, you can store an input level for when MONITOR is on independently of the input levels for the input sources.
2Press the SOUND key repeatedly until the “INPUT” indication appears.
3Use the MULTI CONTROL knob or 5/∞ keys to adjust the input level.
| SP |
|
|
| TI.VOL |
|
|
| FM | DIGITAL |
|
|
|
| A |
| L | C | R |
|
| ||||
|
|
|
|
| MUTE | LFE |
| SW | AM PRO LOGIC S.DIRECT |
|
| |
|
|
|
|
|
| MHz 3 STEREO MONITOR |
|
| ||||
| RDS |
| EON | PTY | LS | S | RS | kHz DOWN MIX | DSP |
|
| |
| TP | TA | NEWS |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
•The adjustment mode is displayed for approximately eight seconds.
•The input level may be adjusted to any one of three settings: 0dB,
Preparations
1 Measure the distance from the listening position to each of |
the speakers. |
Jot down the distance to each of the speakers.
Distance to front speakers: | ____ feet (meters) |
Distance to center speaker: | ____ feet (meters) |
Distance to surround speakers: | ____ feet (meters) |
2Use the MULTI CONTROL knob or 5/∞ keys to select the distance to the front speakers.
The speaker indicator to be adjusted blinks.
| SP |
|
|
| TI.VOL |
|
|
|
|
|
| FM | DIGITAL |
|
| |
|
| A |
| L | C | R |
|
|
|
|
| |||||
|
|
|
|
| MUTE |
|
|
| AM PRO LOGIC S.DIRECT |
|
| |||||
|
|
|
|
| LFE |
| SW |
|
|
| MHz 3 STEREO MONITOR |
|
| |||
| RDS |
| EON | PTY | LS | S | RS |
|
|
| kHz DOWN MIX | DSP |
|
|
| |
| TP | TA | NEWS |
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Indication in feet | Indication in meters |
| ||||||
•The allowable setting range is 1 to 30 feet (0.3 to 9.0 m), adjustable in 1 foot (0.3 m) increments.
3Press the SET UP or display operation 2 [Next] key.
4Repeat steps 2 and 3 to input the distance for each of the speakers.
5Setup is complete when the input indication reappears.
SP A | L | R |
|
| SW |
Display when all speakers have been selected.
•The speakers you have selected should appear on the display. Confirm that all the speakers have been correctly selected.
4Press the SOUND key again to return to the input indication.