Normal playback
Preparing for playback
22
Some preparatory steps are needed before starting playback.
|
|
|
|
|
|
|
| INPUT MODE | ||||||||||||||
POWER ( |
| ) |
|
|
|
|
|
| AUTO/CINEMA EQ. | |||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
INPUT SELECTOR
SPEAKERS A/B
Selecting the input modeIf you have selected a component connected to the CD/DVD,DVD/6ch VIDEO2, or VIDEO3 jacks, make sure that the input mode setting is
correct for the type of audio signal to be used. | 7 |
Select the source name corresponding to the component connected to the MD/TAPE jacks. The initial factory setting is “TAPE”. To change the source to “MD”, follow the steps below:
Operations | 1 Use the INPUT SELECTOR knob to select “MD/TAPE”. | |
2 Hold down the AUTO/CINEMA EQ. key for more than 2 seconds. | ||
| ||
| • The source indication changes to “MD”. | |
| • To return to the original indication, repeat procedure 2. |
Press the SPEAKERS A or B key to select the speaker system to be used.
A ON | : Sound from the speakers connected to the SPEAKERS A |
| terminals on the rear panel. |
B ON | : Sound from the speakers connected to the SPEAKERS B |
| terminals on the rear panel. No sound will be heard from the |
| subwoofer. |
A+B ON | : Sound from both the speakers connected to the SPEAKERS |
A and B terminals on the rear panel.
A+B OFF : No sound from the speakers. Use this setting when listening with headphones for stereo sound in all playback modes.
The indicator for the speakers you want to use should be lit.
SP A B | L | R |
|
| SW |
•Selecting “6ch INPT” by pressing the INPUT MODE key, whereby “DVD/6ch” is the input source will cause SPEAKERS A to be selected automatically.
Turning on the receiver1Turn on the power to the related components.
2 Turn on the power to this receiver by pressing POWER( 
) or SYS. POWER( 
) key.
Listening to a source component
VOLUME CONTROL
INPUT SELECTOR
MUSIC 
MOVIE
+ +
— —
1Use the INPUT SELECTOR knob, MUSIC key, or MOVIE key to select the source you want to listen to.
The input sources change as shown below:
Selecting a source using the INPUT SELECTOR knob
1 “PHONO”
2“TUNER”
3 “CD/DVD”
4 “TAPE” or “MD”
5 “VIDEO1”
6 “VIDEO2”
7 “VIDEO3”
8 “DVD/6ch”
9 “AV AUX”
Selecting a source using the MUSIC key
1 “CD/DVD”
2“TAPE” or “MD”
3 “TUNER”
4 “PHONO”
Selecting a source using the MOVIE key
1 “VIDEO1”
2“VIDEO2”
3 “VIDEO3”
4 “DVD/6ch”
5 “AV AUX”
•MUSIC and MOVIE will not display input sources which are not pre- setup.
2Start playback from the selected source.3Use the VOLUME CONTROL knob or VOL. +/– keys to adjust the volume.