Kohler 38RCL, 48RCL, 60RCL - page 31

TP-6810 11/13 31Section3 RDC2Controller Operation

1. Press the Select button to enter the main menu.

2. Press the down arrow button until the desired

menuis displayed. See Figure 3-7.Dateand Time

are used for this example.

3. PresstheSelect button to enter the Date and Time

menu.

4. To change the date and time settings, press the

Select button again. Theyear will flash.

5. Press the up or down arrow buttons to change the

year.

6. When the correct year is shown, press the Select

button. The year is saved and the next setting

(month) flashes.

7. Repeat steps 5 and 6, using the arrow and select

buttons to set the month and the date.

Press:

Changing Settings on the RDC2 Controller

Press: Display:

Overview ---->

1.2h

Display:

Press: Display:

Press: Display:

Da t e ---- >

andTime

Date:

05Dec2011

8. Whenthe correct date is shown, press the Select

button. The saved date is shown.

9. Press the down arrow button to step to the next

menu.

10. Repeatsteps 5 and 6, using the arrow and select

buttons to set and save the time.

Note: Tochange from am to pm, press the up arrow

key to increase the hour until the correct hour

and pm is displayed.

11. Repeat to set the time format to 12 hr. or 24 hr.

12. Press the down arrow button. Return is

displayed.

13. Press Select to return to the Date and Time

menu.

14. Press the Up or Down arrow buttons to step to a

differentmenu.

15. Press Auto to signal the controller to exit the

menus and return to the generator set status

display.

Note: Ifno buttons are pressed, the controller returns

to the status display after 5 minutes.

Press: Display:

OR

Press: Display:

Press: Display: <---- Return

Press: Display:

Time:

01:49pm

Date ---->

andTime

AUTO

Press: Display: GensetState

Standby

Date:

05Dec2011

Date:

05Dec2012

Press: Display: Date:

05Dec2012

Press: Display: Date:

03Jan2012

Figure 3-6 Changing Settings

Contents

Main WARNING California Proposition 65 Product Identification Information Generator Set Identification Numbers Controller Identification Table of Contents Table of Contents, continued Safety Precautions and Instructions DANGER WARNING CAUTION Accidental Starting Engine Backfire/Flash Fire Exhaust System Fuel System Hazardous Noise CAUTION Hazardous Voltage/ Moving Parts DANGER Heavy Equipment Hot Parts Notice Introduction Nameplate List of Related Literature Figure 3 Related Literature Service Assistance Page Section 1 Service Views Cooling System Detail Figure 1-1 38/48RCL Service Views for Maintenance (38RCL shown) Cooling System Detail Figure 1-2 60RCL Service Views Section 2 Generator Set Operation 2.1 Operating Area 2.2 Prestart Checklist 2.3 Exercising the Generator Set 2.4 Generator Set Operation 2.4.1 Local Starting and Stopping 2.4.2 Automatic Starting and Stopping 2.4.3 Remote Starting and Stopping 2.5 Exercise 2.5.1 Unloaded Cycle Exercise with Complete System Diagnostics 2.5.2 Unloaded Full-Speed Exercise 2.5.3 Loaded Full-Speed Exercise (with RXT only) 2.5.4 Shutdown During Exercise 2.5.5 Power Failure During Exercise 2.5.6 Exerciser Reset 2.5.8 Changing the Exercise Setting Figure 2-2 RDC2 Main Menu See Section 2.5.8, Changing the Exercise Setting 2.6 Faults 2.6.1 Warnings 2.6.2 Shutdowns 2.6.3 ATS Communication Errors 2.6.4 Resetting the Controller after a Fault Shutdown Page Figure 2-5 Controller Fault Messages 2.6.5 Event Log 2.7 Model RXT Transfer Switch Operation 2.7.1 Source Availability 2.7.2 ATSControl Sequence of Operation 2.7.3 Time Delays 2.7.4 ATSLoad Control Relay Time Delay Section 3 RDC2 Controller Operation 3.1 RDC2 Generator Set/Transfer Switch Controller 3.2 Controls and Indicators 3.2.1 Controller Keypad 3.2.2 LED Indicators 3.2.3 LCD Display 3.3 Controller Power 3.4 Battery Charging 3.5 Changing Settings Page 3.6 Controller Menus 3.7 Main Menu 3.8 Overview Menu Figure 3-8 Overview Menu 3.9 Engine Metering Menu Figure 3-9 Engine Metering Menu 3.10 Generator Metering Menu DANGER 3.11 Generator Set Information Menu 3.12 Genset Run Time Menu 3.13 Genset System Menu 3.14 ATS Status Menu 3.15 ATS Configuration Menu 3.16 Date and Time Menu 3.17 Networking Information Menus 3.17.1 Networking Status Submenu 3.17.2 Networking Configuration Submenu (OnCue Password) 3.17.3 RBUS Information Submenu 3.17.4 Remote Devices Submenu Check the status of remote devices communicating through RBUS. Device types can include: Figure 3-21 Remote Devices Submenu 3.18 Programmable Interface Module (PIM) Menus 3.19 Load Control Menus Section 4 Scheduled Maintenance 4.1 General Maintenance 4.2 Service Schedule 4.3 Lubrication System 4.3.1 Oil Specifications 4.3.2 Oil Check 4.3.3 Oil Additions 4.3.4 Oil and Filter Change 4.4 Air Cleaner 4.5 Exhaust System 4.6 Cooling System 4.6.1 Checking and Filling Coolant 4.6.2 Cooling System Inspection 4.6.3 Draining Cooling System 4.6.4 Flushing and Cleaning 4.6.5 Filling Cooling System 4.7 Ignition System 4.8 Battery 4.9 Storage Procedure Page Section 5 Troubleshooting 5.1 Introduction 5.2 USB Port 5.3 Fault Messages 5.4 Circuit Protection 5.5 Generator Set Troubleshooting Figure 5-1 General Troubleshooting Chart 5.6 Controller Troubleshooting Figure 5-2 contains basic troubleshooting information for the RDC2 controller. Figure 5-2 RDC2 TroubleshootingChart Page Appendix A Abbreviations The following list contains abbreviations that may appear in this publication.