Manuals / Brands / Computer Equipment / Tablet Accessory / Kohler / Computer Equipment / Tablet Accessory

Kohler 38RCL, 48RCL, 60RCL 3.17.2 Networking Configuration Submenu (OnCue Password)

1 64

Download 64 pages, 1.78 Mb

TP-6810 11/1342 Section3 RDC2ControllerOperation

3.17.2 Networking ConfigurationSubmenu (OnCue Password)

The networking Configuration menu includes settings

used for communication with the KohlerrOnCuer

Home Generator Management System.

For most applications, DHCP is enabled and the IP

settingscannot be changed from the controller keypad.

If DHCP is enabled, IP parameters are not displayed.

If DHCP is disabled (i.e., if a static IP address is

required),then the IP parameters can be modified. For

applicationsthat require static IP addresses, press and

hold the select button to enable editing, disable DHCP,

and then step to the next parameters and enter the

information.

If an error occurs while setting a parameter, an error

message is displayed and then the controller exits the

edit mode. Previoussettings are preserved.

OnCue Password

Forthe initial OnCue setup, you will be required to reset

theOnCue password on the RDC2 controller, and then

enterit into the OnCue software. Toresetthe password,

follow the instructions in Figure 3-19.

Note: The password is displayed for only 10 seconds.

Be sure to write down the password and serial

number.

A new password is generated each time the reset

password procedure is performed. If the password is

reset after the OnCue system has been set up, the

connection will be lost. Enter the new password in

OnCue to reconnect.

tp6804

<----Return

DHCP:

Enabled

Reset OnCue

Password

Reset OnCue

Password? No

S/N: 1234567

New PW: 12345

PressSelect to enter YES

orNO as displayed. New

passwordis displayed for

approximately10 seconds.

Networking

Configuration

HOLD

Reset OnCue

Password? Yes

UParrow for YES,

Downarrow for NO.

Networking---->

Information

Networking---->

Status

Figure 3-19 Network Configuration Submenu

Contents

Main WARNING California Proposition 65 Product Identification Information Generator Set Identification Numbers Controller Identification Table of Contents Table of Contents, continued Safety Precautions and Instructions DANGER WARNING CAUTION Accidental Starting Engine Backfire/Flash Fire Exhaust System Fuel System Hazardous Noise CAUTION Hazardous Voltage/ Moving Parts DANGER Heavy Equipment Hot Parts Notice Introduction Nameplate List of Related Literature Figure 3 Related Literature Service Assistance Page Section 1 Service Views Cooling System Detail Figure 1-1 38/48RCL Service Views for Maintenance (38RCL shown) Cooling System Detail Figure 1-2 60RCL Service Views Section 2 Generator Set Operation 2.1 Operating Area 2.2 Prestart Checklist 2.3 Exercising the Generator Set 2.4 Generator Set Operation 2.4.1 Local Starting and Stopping 2.4.2 Automatic Starting and Stopping 2.4.3 Remote Starting and Stopping 2.5 Exercise 2.5.1 Unloaded Cycle Exercise with Complete System Diagnostics 2.5.2 Unloaded Full-Speed Exercise 2.5.3 Loaded Full-Speed Exercise (with RXT only) 2.5.4 Shutdown During Exercise 2.5.5 Power Failure During Exercise 2.5.6 Exerciser Reset 2.5.8 Changing the Exercise Setting Figure 2-2 RDC2 Main Menu See Section 2.5.8, Changing the Exercise Setting 2.6 Faults 2.6.1 Warnings 2.6.2 Shutdowns 2.6.3 ATS Communication Errors 2.6.4 Resetting the Controller after a Fault Shutdown Page Figure 2-5 Controller Fault Messages 2.6.5 Event Log 2.7 Model RXT Transfer Switch Operation 2.7.1 Source Availability 2.7.2 ATSControl Sequence of Operation 2.7.3 Time Delays 2.7.4 ATSLoad Control Relay Time Delay Section 3 RDC2 Controller Operation 3.1 RDC2 Generator Set/Transfer Switch Controller 3.2 Controls and Indicators 3.2.1 Controller Keypad 3.2.2 LED Indicators 3.2.3 LCD Display 3.3 Controller Power 3.4 Battery Charging 3.5 Changing Settings Page 3.6 Controller Menus 3.7 Main Menu 3.8 Overview Menu Figure 3-8 Overview Menu 3.9 Engine Metering Menu Figure 3-9 Engine Metering Menu 3.10 Generator Metering Menu DANGER 3.11 Generator Set Information Menu 3.12 Genset Run Time Menu 3.13 Genset System Menu 3.14 ATS Status Menu 3.15 ATS Configuration Menu 3.16 Date and Time Menu 3.17 Networking Information Menus 3.17.1 Networking Status Submenu 3.17.2 Networking Configuration Submenu (OnCue Password) 3.17.3 RBUS Information Submenu 3.17.4 Remote Devices Submenu Check the status of remote devices communicating through RBUS. Device types can include: Figure 3-21 Remote Devices Submenu 3.18 Programmable Interface Module (PIM) Menus 3.19 Load Control Menus Section 4 Scheduled Maintenance 4.1 General Maintenance 4.2 Service Schedule 4.3 Lubrication System 4.3.1 Oil Specifications 4.3.2 Oil Check 4.3.3 Oil Additions 4.3.4 Oil and Filter Change 4.4 Air Cleaner 4.5 Exhaust System 4.6 Cooling System 4.6.1 Checking and Filling Coolant 4.6.2 Cooling System Inspection 4.6.3 Draining Cooling System 4.6.4 Flushing and Cleaning 4.6.5 Filling Cooling System 4.7 Ignition System 4.8 Battery 4.9 Storage Procedure Page Section 5 Troubleshooting 5.1 Introduction 5.2 USB Port 5.3 Fault Messages 5.4 Circuit Protection 5.5 Generator Set Troubleshooting Figure 5-1 General Troubleshooting Chart 5.6 Controller Troubleshooting Figure 5-2 contains basic troubleshooting information for the RDC2 controller. Figure 5-2 RDC2 TroubleshootingChart Page Appendix A Abbreviations The following list contains abbreviations that may appear in this publication.