Manuals / Kramer Electronics / Computer Equipment / Switch

Kramer Electronics VS-88DTP MACHINENAME = Up to 14 Alfa-Numeric chars, Network Setting Commands

Models: VS-88DTP

1 55

Download 55 pages 42.16 Kb

Page 50

MACHINE_NAME = Up to 14 Alfa-Numeric chars.

Identification commands

Command	Syntax		Response
Read machine name	NAME?		NAME
				MACHINE_NAME

Reset machine name to	NAME-RST		NAME-RST
factory default*			MACHINE_FACTORY_NAME
			RESULT

*Note: machine name not equal to model name. This name relevance for site viewer identification of specific machine or for network using (with DNS feature on).

MACHINE_NAME = Up to 14 Alfa-Numeric chars.

* Machine factory name = Model name + last 4 digits from serial number.

Network Setting Commands

Set IP Address

NET-IP

NET-IP

IP_ADDRESS

IP_ADDRESS

RESULT

NTIP

Read IP Address

NET-IP?

NET-IP

IP_ADDRESS

NTIP?

Read MAC Address

NET-MAC?

NET-MAC

MAC_ADDRESS

NTMC

Set subnet mask

NET-MASK

SUBNET_MASK

NET-MASK

SUBNET_MASK

NTMSK

RESULT

Read subnet mask

NET-MASK?

NET-MASK

SUBNET_MASK

NTMSK?

Set gateway address

NET-GATE

NET-GATE

GATEWAY_ADDRESS

GATEWAY_ADDRESS

NTGT

RESULT

Read subnet mask

NET-GATE?

NET-GATE

GATEWAY_ADDRESS

NTGT?

Set DHCP mode

NET-DHCP

DHCP_MODE

NET-DHCP

DHCP_MODE

RESULT

NTDH

Read subnet mask

NET-DHCP?

NET-DHCP

DHCP_MODE

NTDH?

=

DHCP_MODE

0 – Don't use DHCP (Use IP set by factory or IP set command).

1 – Try to use DHCP, if unavailable use IP as above.

Change protocol ethernet

ETH-PORT

PROTOCOL

,

PORT

ETH-PORT

PROTOCOL

,PORT

port

ETHP

RESULT

Read protocol ethernet

ETH-PORT?

ETH-PORT

,

PROTOCOL

PROTOCOL

PORT

port

ETHP?

= TCP / UDP

(transport layer protocol)

PROTOCOL

PORT = ethernet port to enter protocol 3000 commands.

1-65535 = User defined port

0 - reset port to factory default (50000 for UDP, 5000 for TCP)

46	VS-88DTP - Kramer Protocol

Image 50

Kramer Electronics VS-88DTP user manual MACHINENAME = Up to 14 Alfa-Numeric chars, 1-65535 = User defined port

Contents

VS-88DTP 8x8 DVI - Twisted Pair Matrix SwitcherUSER MANUAL MODELPage Connecting the VS-88DTP ContentsInstalling the VS-88DTP in a Rack Technical SpecificationsFigures 1 Introduction 2.1 Achieving the Best Performance 2.2 Safety Instructions2 Getting Started 2.3 Recycling Kramer Products VS-88DTP - Getting Started3 Overview 3.1 Defining the VS-88DTP 8x8 DVI - Twisted Pair Matrix Switcher VS 88DTP - Overview Function FeatureVS 88DTP - Overview 3.2 Using the IR Transmitter This section provides instructions for rack mounting the unit 4 Installing the VS-88DTP in a RackVS-88DTP - Installing the VS-88DTP in a Rack 5 Connecting the VS-88DTP 5.1 Connecting to the VS-88DTP via RS-232 To set the RS-485 machine number using the DIP-switches 5.2 Connecting a PC or Controller to the RS-485 Port5.2.1 Setting the RS-485 Machine Number To connect a device with a RS-485 port to the VS-88DTP5.2.2 Setting the RS-485 Bus Termination VS-88DTPSection 5.2.3 Connecting and Controlling Multiple VS-88DTP DevicesTo daisy-chain up to 16 VS-88DTP devices Select Properties 5.3 Connecting the VS-88DTP via Ethernet5.3.1 Connecting to the Ethernet Port Directly to a PC The Local Area Connection Properties window appears 4. Select PropertiesVS-88DTP - Connecting the VS-88DTP 7. Click OK5.3.2 Connecting to the Ethernet Port via a Network Hub VS-88DTP - Connecting the VS-88DTP6.1 Routing Inputs to Outputs 6.2 Disconnecting Outputs6 Operating the VS-88DTP To route an input to an outputTo store a setup 6.3 Storing and Recalling Setups in Presets6.4 Switching Between Protocol 2000 and Protocol To recall a setup6.5.2 Acquiring an EDID from Several Outputs to Several Inputs 6.5 Acquiring the EDID6.5.1 Acquiring an EDID from a Single Output To acquire or change the EDID from a single output6.5.3 Acquiring the Default EDID To reset to the default EDID, do the followingTo lock and unlock the front panel buttons 6.7 Control Configuration via the Ethernet Port6.6 Locking and Unlocking the Front Panel Buttons 7.1 Connecting to the VS-88DTP via your Browser 7 Controlling the VS-88DTP Remotely via EthernetFigure 11 Entering the IP Number in the Address Bar If you are using DHCP, you have to enter the nameThe Loading page appears Figure 12 The Loading PageThere are two remote operation Web pages Main switching matrix see Section Configuration see Section3. Click Run VS-88DTP - Controlling the VS-88DTP Remotely via EthernetTo switch an input to an output, for example, input 1 to output 7.2 The Main Switching Matrix Page7.2.1 Switching an Input to an Output 7.2.2 Operating in the Offline Mode To operate in the Offline mode7.2.3 Storing and Recalling Setups To store a switching configurationTo recall a setup 2. Click Store A confirmation message appears 3. Click OKFigure 19 Recalling a Preset in Offline Mode The configuration from Preset 03 is loadedFigure 18 Selecting Preset 2. Click Recall A confirmation message appears 3. Click OKTo lock the front panel buttons 7.3 The Configuration Page7.2.4 Locking the Front Panel Buttons To edit the IP-related settings 8 Technical Specifications VS-88DTP - Technical SpecificationsEDID 9 Default Communication ParametersSwitching Protocol RS-232VS-88DTP - Default EDID 10 Default EDIDEach input on the VS-88DTP is loaded with a factory default EDID VS-88DTP - Default EDID Report InformationVS-88DTP - Updating the VS-88DTP Firmware 11 Updating the VS-88DTP FirmwareInstructions for upgrading the VS-88DTP firmware can be found at 12 Table of ASCII Codes for Serial Communication Protocol 38 VS-88DTP - Table of ASCII Codes for Serial Communication Protocol13 Hex Codes for Serial Communication Protocol 14.2.1.1 Simple Command 14.1 Switching Protocols14.1.1 Switching Protocols via the Front Panel Buttons 14 Kramer ProtocolCommand 14.2.1.2 Command String14.2.3 Command Terms 14.2.214.2.6 Command Chaining 14.2.4 Entering Commands14.2.5 Command Forms Command chain separator characterA separate response is sent for every command in the chain 14.2.7 Maximum String Length14.2.8 Backward Support 64 charactersExamples this is 4x4 matrixREVISION VS-88DTP - Kramer ProtocolBUILD COUNTNetwork Setting Commands PORT = ethernet port to enter protocol 3000 commands0 - reset port to factory default 50000 for UDP, 5000 for TCP MACHINENAME = Up to 14 Alfa-Numeric charsDESTINATION 14.3 Kramer ProtocolVS-88DTP - Kramer Protocol INSTRUCTIONDefinition for Specific Instruction Instruction Codes for ProtocolInstruction Description InputVS-88DTP - Kramer Protocol Page E-mail info@kramerel.com SAFETY WARNINGWe welcome your questions, comments, and feedback