Manuals / LevelOne / Computer Equipment / Network Router

LevelOne GSW-2490TXM manual Connecting to the Network, Pre-Installation Requirements

Models: GSW-2490TXM

1 57

Download 57 pages 1.26 Kb

Page 8

Image 8

LEDs will soon flash red.

When the Switch passes the self-test within 15 seconds, the Link /ACT LED turns on.

Note : If the Switch fails the self-test, the Diag LED will blink.

Connecting to the Network

This section provides the installation procedure and instructions for assigning IP address.

Pre-Installation Requirements

Before you start hardware installation, make sure your installation environment has below items:

PCs with 10/100Mbps Ethernet NICs/ 100Mbps Fiber NICs: Your PC must have a standard Ethernet interface to connect to the Switch.

UTP cable with RJ45 connectors/ Fiber cable with MT-RJ/ VF-45 connectors: Check if the cable and connectors work properly.

A power outlet: 100 to 240V AC at 50 to 60 Hz: Make sure that the Switch power is accessible and cables can be connected easily.

Page 8

Image 8

LevelOne GSW-2490TXM manual Connecting to the Network, Pre-Installation Requirements

Contents

GSW-2490TXM 1. Introduction24-Port + 2 Slide-in Slots SNMP Switch LevelOneFeatures Package Contents Management Methods Console and Telnet ManagementSNMP Network Management Figure 1-2. Package ContentsHardware Description Hardware DescriptionThe Front Panel 10/100Base-TX RJ-45 ports Auto MDI/MDIXLED Indicators Expansion SlotsConsole Port Figure 2-2 The LED IndicatorsPower On Diagnostic TestRear Panel Table 2-1. The Descriptions of LED IndicatorsNote If the Switch fails the self-test, the Diag LED will blink Connecting to the NetworkPre-Installation Requirements Mounting the Switch Desktop Mountingon the bottom of the Switch Figure 3-1. Attaching Rubber Feet to each cornerRack-mounted Installation Figure 3-2. Attach mounting brackets with screwsConnecting to the Switch Baud Rate 9600 bps Data Bits Parity none Stop Bit Control flow None Login in the Console InterfaceFigure 3-5. The settings of communication parameters Figure 3-6. The screen of Main Menu Main Menu1. System Information 2. Management Setup 2.1. Network ConfigurationFigure 3-8. The Management Setup Menu Figure 3-7. The System Information Menu2.2. Serial Port Configuration 2.3. SNMP Community SetupFigure 3-9. The Network Configuration Men Figure 3-10. The Serial Port Configuration2.5. Management Capability Setup 2.4. Trap ReceiverFigure3-11. The SNMP Community Menu Figure 3-12. The Trap Receiver MenuFigure 3-14. The Trap Filter Setup menu 2.6. Trap Filter SetupFigure 3-13. The Management Capability setup Menu 3.1. Switch Device Configuration 3. Device Control MenuFigure 3-16. The Switch Device Configuration menu Figure 3-15. The Device Control menuFigure 3-17. The Switch Port Configuration menu 3.2. Switch Port Configuration3.3. Permanent Address Configuration 3.3.1. Static Unicast Address Configuration 3.3.2. Static Multicast Address Configuration3.4. Port Statistics Figure 3-18. The Permanent Address Configuration menuFigure 3-19. The Port Statistics menu 3.5. Spanning Tree Protocol ConfigurationFigure 3-20. The Spanning Tree Protocol Configuration menu 3.6. Spanning Tree Protocol Port Configuration 3.7. Post-Based VLAN ConfigurationFigure 3-21. The Spanning Tree Protocol port Configuration menu Figure 3-22. The Port Based VLAN Configuration menu3.8. 802.1Q VLAN Configuration 3.8.1. 802.1Q VLAN Configuration3.8.2. Dynamic VLAN Table Figure 3-23. The Port Based VLAN Configuration menu3.8.3. VLAN Untagged Configuration 3.8.4 GARP ConfigurationFigure 3-25. The Port Untag Configuration menu Figure 3-24. The Dynamic VLAN Table menu3.9. MTU/MDU Per-Port VLAN Table Figure 3-26. The GARP Configuration menuGARP Leave All Time GARP Leave Time GARP Join Time Figure 3-27. The MTU/MDU Per-Port VLAN Table menuFigure 3-28. The IGMP Snooping Table 3.11. Trunk Group Configuration3.10. IGMP Snooping Table Figure 3-30. The Port Mirroring Configuration Menu 3.12. Port Mirroring ConfigurationFigure 3-29. The Trunk Configuration Menu 4. User Authentication Figure 3-31. The User Authentication Menu5.2 Factory Reset 5.3 Login Timeout Interval5. System Utility 5.1 System Restart Figure 3-33. The Factory Reset MenuWeb-Based Management 5.4 System DownloadFigure 3-34. The Login Timeout Interval Figure 3-35. The System Download MenuFigure 4-1 The Password Window System LoginAbout Web-based Management Management Setup Network ConfigurationSystem Information Figure 4-3. The Network Configuration MenuFigure 4-4. The Serial Port Configuration Menu Serial Port ConfigurationSNMP Community Setup Figure 4-6. The Trap Receiver Menu Trap ReceiverFigure 4-5. The SNMP Community Setup Menu Management Capability Setup Trap Filter SetupFigure 4-7. The Management Capability Setup Menu Figure 4-8. The Trap Filter Setup MenuSwitch Configuration Device ControlFigure 4-9. The Switch Configuration upper Menu Figure 4-10. The Switch Configuration lower MenuSwitch Port Configuration Figure 4-13. The Port Mirror in Switch Port Configuration Menu Permanent Address ConfigurationFigure 4-12. The Trunk Group in Switch Port Configuration Menu Page Spanning Tree Protocol Configuration Figure 4-16. The Spanning Tree Protocol Configuration upper MenuFigure 4-18. The Spanning Tree Protocol Port Configuration upper Menu Spanning Tree Protocol Port ConfigurationFigure 4-17. The Spanning Tree Protocol Configuration lower Menu VLAN Configuration Port StatisticsFigure 4-19. The Spanning Tree Protocol Port Configuration lower Menu Figure 4-20. The Port Statistics MenuFigure 4-21. The Static VLAN Configuration Menu Figure 4-22. The Dynamic VLAN Table MenuFigure 4-23. The Untagged Configuration Menu Figure 4-26. The GARP Configuration Menu GARP ConfigurationIGMP Configuration Figure 4-28. The User Authentication Menu User AuthenticationFigure 4-27. The IGMP Configuration Menu Factory Reset System UtilitySystem Restart Figure 4-30. The Factory Reset MenuLogin Timeout Interval Update SettingSystem Download Figure 4-31. The Login Timeout Interval MenuNetwork Configuration Figure 4-32. The Update Setting MenuCollapsed Backbone Application Departmental Bridge Figure 5-1. Collapsed Backbone ApplicationHigh Performance Switched Workgroup Figure 5-2 Departmental Bridge ApplicationIEEE 802.1Q VLAN Application Port-based VLAN WorkgroupShared Server Figure 5-5 Shared ServerProduct Specifications Media connectorSwitch Technology ProtocolSystem Power, per port Link/active 8K MAC address with auto learning function6Mb share memory FDX/Col,10/100Mbps