Manuals / LevelOne / Computer Equipment / Network Router

LevelOne GSW-2490TXM manual Mounting the Switch, Desktop Mounting, on the bottom of the Switch

Models: GSW-2490TXM

1 57

Download 57 pages 1.26 Kb

Page 9

Mounting the Switch

Dedicated power supply: Use dedicated power circuits or power conditioners to supply reliable electrical power to the network devices.

A dry cool place: Keep the Switch away from moisture. Avoid direct sunlight, heat source, and high amount of electromagnetic interference around.

Mounting tools: If you intend to mount the Switch on a rack, make sure you have all the tools, mounting brackets, screws

etc.

Caution:

Cabling must be away from sources of electrical noise such as radio, computers, transmitters, broadband amplifiers, power lines and keep away from TVs, hair dryers, and microwave.

Air flow around the Switch and through its vents on the rear cannot be restricted.

Mounting the Switch

The LevelOne GSW-2490TXM SNMP Switch is suitable for use in an office environment where it can be rack-mounted in standard EIA 19-inch racks or standalone.

Desktop Mounting

1.Set the Switch on a sufficiently large flat space with a power outlet nearby, and about the center of all networked devices.

2.Make sure mounting surface on the bottom of the Switch is grease dust free.

3.Remove adhesive backing from your Rubber Feet.

Figure 3-1. Attaching Rubber Feet to each corner

on the bottom of the Switch

4.Apply the Rubber Feet to each corner on the bottom of the Switch. These footpads can prevent the Switch from shock/vibrations.

9

Image 9

LevelOne GSW-2490TXM manual Mounting the Switch, Desktop Mounting, 1. Attaching Rubber Feet to each corner

Contents

1. Introduction GSW-2490TXM24-Port + 2 Slide-in Slots SNMP Switch LevelOneFeatures Package Contents Console and Telnet Management Management MethodsSNMP Network Management Figure 1-2. Package ContentsHardware Description Hardware DescriptionThe Front Panel 10/100Base-TX RJ-45 ports Auto MDI/MDIXExpansion Slots LED IndicatorsConsole Port Figure 2-2 The LED IndicatorsDiagnostic Test Power OnRear Panel Table 2-1. The Descriptions of LED IndicatorsConnecting to the Network Pre-Installation RequirementsNote If the Switch fails the self-test, the Diag LED will blink Desktop Mounting Mounting the Switchon the bottom of the Switch Figure 3-1. Attaching Rubber Feet to each cornerFigure 3-2. Attach mounting brackets with screws Rack-mounted InstallationConnecting to the Switch Login in the Console Interface Figure 3-5. The settings of communication parametersBaud Rate 9600 bps Data Bits Parity none Stop Bit Control flow None Main Menu 1. System InformationFigure 3-6. The screen of Main Menu 2.1. Network Configuration 2. Management SetupFigure 3-8. The Management Setup Menu Figure 3-7. The System Information Menu2.3. SNMP Community Setup 2.2. Serial Port ConfigurationFigure 3-9. The Network Configuration Men Figure 3-10. The Serial Port Configuration2.4. Trap Receiver 2.5. Management Capability SetupFigure3-11. The SNMP Community Menu Figure 3-12. The Trap Receiver Menu2.6. Trap Filter Setup Figure 3-13. The Management Capability setup MenuFigure 3-14. The Trap Filter Setup menu 3. Device Control Menu 3.1. Switch Device ConfigurationFigure 3-16. The Switch Device Configuration menu Figure 3-15. The Device Control menu3.2. Switch Port Configuration 3.3. Permanent Address ConfigurationFigure 3-17. The Switch Port Configuration menu 3.3.2. Static Multicast Address Configuration 3.3.1. Static Unicast Address Configuration3.4. Port Statistics Figure 3-18. The Permanent Address Configuration menu3.5. Spanning Tree Protocol Configuration Figure 3-20. The Spanning Tree Protocol Configuration menuFigure 3-19. The Port Statistics menu 3.7. Post-Based VLAN Configuration 3.6. Spanning Tree Protocol Port ConfigurationFigure 3-21. The Spanning Tree Protocol port Configuration menu Figure 3-22. The Port Based VLAN Configuration menu3.8.1. 802.1Q VLAN Configuration 3.8. 802.1Q VLAN ConfigurationFigure 3-23. The Port Based VLAN Configuration menu 3.8.2. Dynamic VLAN Table3.8.4 GARP Configuration 3.8.3. VLAN Untagged ConfigurationFigure 3-25. The Port Untag Configuration menu Figure 3-24. The Dynamic VLAN Table menuFigure 3-26. The GARP Configuration menu 3.9. MTU/MDU Per-Port VLAN TableGARP Leave All Time GARP Leave Time GARP Join Time Figure 3-27. The MTU/MDU Per-Port VLAN Table menu3.11. Trunk Group Configuration 3.10. IGMP Snooping TableFigure 3-28. The IGMP Snooping Table 3.12. Port Mirroring Configuration Figure 3-29. The Trunk Configuration MenuFigure 3-30. The Port Mirroring Configuration Menu Figure 3-31. The User Authentication Menu 4. User Authentication5.3 Login Timeout Interval 5.2 Factory Reset5. System Utility 5.1 System Restart Figure 3-33. The Factory Reset Menu5.4 System Download Web-Based ManagementFigure 3-34. The Login Timeout Interval Figure 3-35. The System Download MenuSystem Login About Web-based ManagementFigure 4-1 The Password Window Network Configuration Management SetupSystem Information Figure 4-3. The Network Configuration MenuSerial Port Configuration SNMP Community SetupFigure 4-4. The Serial Port Configuration Menu Trap Receiver Figure 4-5. The SNMP Community Setup MenuFigure 4-6. The Trap Receiver Menu Trap Filter Setup Management Capability SetupFigure 4-7. The Management Capability Setup Menu Figure 4-8. The Trap Filter Setup MenuDevice Control Switch ConfigurationFigure 4-9. The Switch Configuration upper Menu Figure 4-10. The Switch Configuration lower MenuSwitch Port Configuration Permanent Address Configuration Figure 4-12. The Trunk Group in Switch Port Configuration MenuFigure 4-13. The Port Mirror in Switch Port Configuration Menu Page Figure 4-16. The Spanning Tree Protocol Configuration upper Menu Spanning Tree Protocol ConfigurationSpanning Tree Protocol Port Configuration Figure 4-17. The Spanning Tree Protocol Configuration lower MenuFigure 4-18. The Spanning Tree Protocol Port Configuration upper Menu Port Statistics VLAN ConfigurationFigure 4-19. The Spanning Tree Protocol Port Configuration lower Menu Figure 4-20. The Port Statistics MenuFigure 4-22. The Dynamic VLAN Table Menu Figure 4-21. The Static VLAN Configuration MenuFigure 4-23. The Untagged Configuration Menu GARP Configuration IGMP ConfigurationFigure 4-26. The GARP Configuration Menu User Authentication Figure 4-27. The IGMP Configuration MenuFigure 4-28. The User Authentication Menu System Utility Factory ResetSystem Restart Figure 4-30. The Factory Reset MenuUpdate Setting Login Timeout IntervalSystem Download Figure 4-31. The Login Timeout Interval MenuFigure 4-32. The Update Setting Menu Network ConfigurationCollapsed Backbone Application Figure 5-1. Collapsed Backbone Application Departmental BridgeFigure 5-2 Departmental Bridge Application High Performance Switched WorkgroupPort-based VLAN Workgroup IEEE 802.1Q VLAN ApplicationFigure 5-5 Shared Server Shared ServerMedia connector Product SpecificationsSwitch Technology Protocol8K MAC address with auto learning function System Power, per port Link/active6Mb share memory FDX/Col,10/100Mbps