Manuals / Brands / Computer Equipment / Power Supply / Liebert / Computer Equipment / Power Supply

Liebert GXT2-10000RT208 6.4 Install the Internal Battery Packs

1 56

Download 56 pages, 2.51 Mb

Installation and Configuration

17

6.4 Install the Internal Battery Packs

To facilitate shipping and installation, the Liebert GXT2-10000RT208 ships without the internal bat-

tery packs installed. Once the UPS is installed in place, the internal battery packs must be installed.

1. Unpack the two internal battery packs from their shipping container.

2. Lift one battery pack from its packaging, holding it in the center of the pack.

3. Align the battery pack so that the cable is at the top right closest to the power module in the

frame.

4. Slip the back of battery pack into the battery compartment and slide it in until the battery

reaches the back of the UPS.

5. Install the battery bracket on the front of the battery pack with two screws.

6. Connect the two slotted connectors and tuck the wires in around the battery pack handles.

7. Repeat for the second battery pack.

8. Install the battery cover grille, tightening the three screws.

9. For tower installation, place the vertical overlay over the controls and indicators (see Figure 8).

10. Install the two front bezels.

!

UPStation GXT

Mjfcfsu

!

UPStation GXT

Battery

Battery

Cover

Front

Bezel

!

UPStation GXT

Liebert

!

UPStation GXT

Controls and

Indicators

(horizontal overlay)

Front of Battery

Battery

Connector

Battery Compartment

Battery

Bracket

DISCONTINUED

PROD U C T

Contents

Main Page TABLE OF CONTENTS Page Page FIGURES TABLES IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS !WARNING !CAUTION 1.0 GLOSSARY OF SYMBOLS ! i 2.0 INTRODUCTION AND SYSTEM DESCRIPTION 3.0 SYSTEM DESCRIPTION 3.1 Transient Voltage Surge Suppression (TVSS) and EMI/RFI Filters 3.2 Rectifier/Power Factor Correction (PFC) Circuit 3.3 Inverter 3.4 Battery Charger 3.5 DC to DC Converter 3.6 Battery 3.7 Static Bypass 4.0 MAJOR COMPONENTS 4.1 Main Frame and Electronics 4.2 Internal Battery Pack Major Components 8 4.3 Input/Output Terminal Blocks and Optional Output Distribution INPUT Figure 4 Optional output distribution modules L1 N L2NL1 L2 OUTPUT H-POTED PASS 5.0 WHATS INCLUDED 6.0 INSTALLATION AND CONFIGURATION 6.1 Install the Main Cabinet 6.1.1 Tower UPS Installation Attach Bezels to Top 6.1.2 Installing the Adjustable Rack-Mount KitSold Separately ! 6.2 External Battery Cabinet Installation 6.3 Connect Input/Output Power 6.3.1 Distribution Module Electrical Connections UPS 6.3.2 Input & Output Terminal Block Connections 6.3.3 Add an Output Power Distribution ModuleOptional 6.4 Install the Internal Battery Packs 7.0 INITIAL STARTUP AND ELECTRICAL CHECKS 7.1 Hardwire Input Connections 7.2 Output Receptacle Distribution Options 8.0 CONFIGURATION PROGRAM 8.1 Liebert GXT2-10000RT208 Configuration Program Features 8.2 What You Will Need 8.3 Configuration ProgramInstallation 8.4 Establishing Communication Link with the UPS 8.5 Configuration ProgramOperation 8.5.1 Read/Confirm UPS Configuration Settings 8.5.2 Cancel Without Changing UPS Settings 8.5.3 Changing UPS Settings 8.5.4 On-Screen Reminders 8.5.5 Programming Rejected When UPS is Off Partial Rejection 8.6 8.6.1 Output Voltage Output Voltage Selection Notes 8.6.2 L-N Reverse Detection120V UPS Models Only 8.6.3 Frequency Selection 8.7 Options Tab 8.8 8.9 8.9.1 Low Battery Time Warning 8.9.2 Auto Battery Test Time 8.9.3 Battery Cabinets Number 8.9.4 Auto Battery Test Page 9.0 CONTROLS AND INDICATORS 9.1 ON/Alarm Silence/Battery Test Button 9.2 OFF/Bypass Button Page 10.0 MODES OF OPERATION 10.1 Normal Mode Operation 10.2 Battery Mode Operation 10.3 Battery Recharge Operation 11.0 C 11.1 Communications Interface Port 11.1.1 DB-9 Interface Port 11.1.2 CommunicationsLiebert SNMP/OCWEBCARD SNMP Adapter 11.2 Pin 4 - Remote Shutdown on Battery 11.3 UPS Intelligent Communications 11.4 Remote Emergency Power Off 12.0 M 12.1 Battery Replacement 12.1.1 Internal Battery Replacement Procedures 12.2 UPS Power Module Replacement Figure 10 UPS back panelcontrol location Figure 11 Power module replacement 13.0 T Table 3 Fault indicators Indicator status Diagnosis/Audible alarm Page Table 5 Troubleshooting guide Problem Cause Solution Table 5 Troubleshooting guide (continued) Problem Cause Solution Page 13.1 Auto-Learning Battery Run Times 14.0 S Table 7 UPS specifications Table 8 Battery specifications Table 9 Optional output distribution specificationsPD-101 Table 7 UPS specifications (continued) Table 10 Optional output distribution specificationsPD-102 Table 11 Optional output distribution specificationsPD-103 Table 12 Replacement 10kVA power module specifications Model Number GXT2-10KPWR208 14.1 Product Warranty Registration Page Page Ensuring The High Availability 0f Mission-Critical Data And Applications. Technical Support / Service Locations