|
| TROUBLESHOOTING | |||||
|
|
|
|
|
|
|
|
|
| USING THE STATUS LED TO |
| ||||
|
| TROUBLESHOOT SYSTEM PROBLEMS |
| ||||
|
| The Power Wave / Power Feed are best diagnosed as |
| ||||
|
| a system. Each component (power source, user inter- |
| ||||
|
| face, and feed head) has a status light, and when a |
| ||||
|
| problem occurs it is important to note the condition of |
| ||||
|
| each. |
|
|
|
|
|
|
| Included in this section is information about the power |
| ||||
|
| source Status LED, and some basic troubleshooting |
| ||||
|
| charts for both machine and weld performance. |
| ||||
|
| The STATUS LIGHT is a two color light that indicates |
| ||||
|
| system errors. Normal operation is a steady green |
| ||||
|
| light. Error conditions are indicated in the following |
| ||||
|
| chart. |
|
|
|
|
|
|
| NOTE: The POWER WAVE F355i (CE) status light |
| ||||
|
| will flash green, and sometimes red and green, for up |
| ||||
|
| to one minute when the machine is first turned on. |
| ||||
|
| This is a normal situation as the machine goes |
| ||||
|
| through a self test at power up. |
| ||||
|
|
|
|
|
|
|
|
|
| Light |
| Meaning |
| ||
|
| Condition |
|
|
|
| |
|
| Steady Green | System OK. Power source communicating normal- |
| |||
|
|
|
| ly with wire feeder and its components. |
| ||
|
|
|
|
|
|
|
|
|
| Blinking |
| Occurs during a reset, and indicates the |
| ||
|
| Green |
| POWER WAVE F355i (CE) is mapping |
| ||
|
|
|
| (identifying) each component in the system. |
| ||
|
|
|
| Normal for first |
| ||
|
|
|
| turned on, or if the system configuration is |
| ||
|
|
|
| changed during operation |
| ||
|
|
|
|
|
|
| |
|
| A l t e r n a t i n g |
| ||||
|
| Green | and | Status light is flashing any combination of |
| ||
|
| Red |
| red and green, errors are present in the |
| ||
|
|
|
| POWER WAVE F355i (CE). Read the error |
| ||
|
|
|
| code before the machine is turned off. |
| ||
|
|
|
| Error Code interpretation through the Status |
| ||
|
|
|
| light is detailed in the Service Manual. |
| ||
|
|
|
| Individual code digits are flashed in red with |
| ||
|
|
|
| a long pause between digits. If more than |
| ||
|
|
|
| one code is present, the codes will be sepa- |
| ||
|
|
|
| rated by a green light. |
| ||
|
|
|
| To clear the error, turn power source off, and |
| ||
|
|
|
| back on to reset. See Troubleshooting |
| ||
|
|
|
| Section. |
| ||
|
|
|
|
|
|
| |
|
| Steady Red | Non recoverable hardware fault. Generally |
| |||
|
|
|
| indicates nothing is connected to the |
| ||
|
|
|
| POWER WAVE F355i (CE) wire feeder |
| ||
|
|
|
| receptacle. See Trouble Shooting Section. |
| ||
|
|
|
|
|
| ||
|
| Blinking Red | Not applicable. |
| |||
|
|
|
|
|
|
|
|
