INSTALLATION | ||
|
|
|
WARNING
ELECTRIC SHOCK can kill.
•Turn the input power OFF at the disconnect switch or fuse box before working on this equipment.
1.Set the High/Low switch code on Feed Head PC board as follows:
2.Turn off power to the power source at the dis- connect switch.
3.Remove the front cover from the power source.
4.The wire feed head board is on the left side of the power source. Locate the
5.Using a pencil or other small object, slide the switch to the OFF position, when the low speed gear is installed. Conversely, slide the switch to the ON position when the high speed gear is installed.
6.Replace the cover and screws. The PC board will “read” the switch at power up, automatically adjust- ing all control parameters for the speed range selected.
DIP Switch Settings and Locations
(See Figure A.1)
DIP switches on the P.C. Boards allow for custom configuration of the Power Wave. To access the DIP switches:
WARNING
•Turn off power at the disconnect switch.
•Remove the top four screws securing the front access panel.
•Adjust the DIP switches as necessary.
•Replace the panel and screws, and restore power.
Control Board DIP Switch:
switch 1 = Object Instance LSB 1 (see table 1) switch 2 = Object Instance MSB 2 (see table 1) switch 3 = Equipment Group 1 Select
switch 4 = Equipment Group 2 Select switch 5 = Equipment Group 3 Select switch 6 = Equipment Group 4 Select switch 7 = reserved for future use switch 8 = work sense lead
1 LEAST SIGNIFICANT BIT
2 MOST SIGNIFICANT BIT
switch 8 | work sense lead |
off | work sense lead not connected* |
on | work sense lead connected |
Feed Head Board DIP Switch:
switch 1 = Object Instance LSB (see table 1) switch 2 = Object Instance MSB (see table 1) switch 3 = Equipment Group 1 Select switch 4 = Equipment Group 2 Select switch 5 = Equipment Group 3 Select switch 6 = Equipment Group 4 Select switch 7 = negative polarity switch
|
|
| switch 7 |
| electrode polarity |
| ||||||||
|
|
|
| off |
|
|
|
|
| positive * |
|
| ||
|
|
|
| on |
|
|
|
|
| negative |
|
| ||
|
|
|
|
|
| |||||||||
switch 8 = high speed gear |
|
| ||||||||||||
|
|
|
|
|
|
|
|
| ||||||
|
|
| switch 8 |
| wire drive gear |
|
| |||||||
|
|
|
| off |
|
|
|
| low speed gear * |
| ||||
|
|
|
| on |
|
|
|
| high speed gear |
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| TABLE 1 |
|
| |
|
|
| Object Instance |
|
| |||||||||
|
|
|
|
|
|
|
| |||||||
|
|
| switch 2 |
| switch 1 |
| Instance | |||||||
|
|
|
| off |
|
|
|
| off |
| 0 * | |||
|
|
|
| off |
|
|
|
| on |
| 1 | |||
|
|
|
| on |
|
|
|
| off |
| 2 | |||
|
|
|
| on |
|
|
|
| on |
| 3 | |||
*Factory Setting |
|
|
|
|
| |||||||||
FEED HEAD BOARD DIP SWITCH |
| FIGURE A.1 |
|
| ||||||||||
|
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 |
|
|
|
|
|
|
O |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
N |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CONTROL BOARD DIP SWITCH
O
N
1 2 3 4 5 6 7 8
LOCATION OF DIP SWITCHES IN MACHINE
