Linear RE-1 manual Transmitter Programming, Telephone Programming

TRANSMITTER PROGRAMMING

Adding Transmitters

Up to 24 groups of transmitters can be assigned common access privileges sharing the same one or two time zones. Up to 100 transmitters total in all groups combined can be used in each RE-1 system.

Press: Number Facility Code First ID

Time Zone 1 Time Zone 2

Number = Number of transmitters in the group

Facility Code = Facility code 0-15 marked on block of transmitters; First ID = 5-digit ID number of first transmitter in group.

Time Zone 1 = 0 = no time zone; 1-7 to restrict access per time zone 1-7 Time Zone 2 = 0 = no time zone; 1-7 to restrict access per time zone 1-7

✦NOTE: If the Time Zone 1 entry is set to “0”, the Time Zone 2 entry is ignored.

Suspend or Activate a Transmitter

Each transmitter programmed can be individually suspended from use for access with this programming PPN. The transmitter will remain suspended until it is re-activated using this same programming PPN.

Press: Facility ID Action

Facility = Facility code 0-15 of transmitter

ID = 5-digit ID number of transmitter

Action: 0 = Suspend transmitter; 1 = Re-activate transmitter

Erasing All Transmitters

★WARNING: Performing this command will remove all transmitters from the memory.

Press: 000000 000000

Assigning Transmitter Buttons to RelaysDefaults: Left (or Top Left) = Relay #1 Right (or Top Right) = Relay #2 Top Button = Both Relays Lower Left = None Lower Right = None

The RE-1 can be programmed to control which relay will activate from which transmitter button. This setting will effect all transmitters (single and multi-channel) used with the RE-1

Press: Button Relay

Button: 1 = Right (or Top Right); 2 = Left (or Top Left) 4 = Top; 5 = Bottom Right; 6 = Bottom Left

Relay: 0 = None; 1 = Relay #1; 2 = Relay #2; 3 = Both Relays

TELEPHONE PROGRAMMING

Maximum Number of Visitor Rings Default: 5 Rings

Changes the maximum number of distinctive rings that the RE-1 will generate to the local telephones when the CALL button is pressed.

Press: Rings

Rings = 1-15 Rings maximum

Call Forwarding Dialing Method Default: Tone

Sets the dialing method used during call forwarding to either tone or pulse style.

Press: Method

Method: 1 = Pulse; 2 = Tone

Visitor Talk Time Limit Default: 60 Seconds

Sets the time that the visitor is allowed to talk to the resident. Ten seconds before the time expires, the voice synthesizer will announce “ten seconds”, and at fi ve seconds it will announce “five seconds”, to the visitor. If the voice synthesizer is disabled (PPN #44), a beep will sound each second during the last ten seconds of time allowed.

Press: Limit

Limit = 15-255 Seconds allowed

Call Waiting Feature On/Off Default: On

Turns the call waiting feature on or off. If call waiting is on (factory default) and the resident is on the telephone at the same time a visitor calls, the RE-1 will generate beeps on the resident’s telephone line to signal that a visitor is calling. The resident has the option to switch to the visitor’s call.

If the call waiting feature is off and the resident is on the telephone at the same time a visitor calls, the RE-1 will announce “resident busy” to the visitor.

Press: Call Waiting

Call Waiting: 1 = ON; 0 = OFF

Privacy Feature Schedule Default: Off

The privacy feature will block visitor’s calls and call forwarding during the selected Time Zone or at all times. If the privacy feature is active and a visitor calls, the RE-1 will announce “do not disturb resident”. If call forwarding is scheduled (PPN #54) and the privacy feature is active, the RE-1 will announce “do not disturb resident” and visitor’s call will not be forwarded.

Press: Privacy Time Zone

Privacy: 0 = Privacy feature OFF

1 = Privacy feature ON (scheduled by Time Zone)

2 = Privacy feature ON at all times

Time Zone = 1-7 (Privacy feature active during this Time Zone)

Intercom Mode On/Off Default : Off

	BOTH
	FUNCTION
	AS LEFT	LEFT
	BUTTON
		BUTTON
		ACT-31
		SINGLE-CHANNEL
MDT		TRANSMITTERS	ACT-21

RIGHT

BUTTON

LEFT

BOTTOM-LEFT BUTTON BUTTON

BOTTOM-RIGHT

BUTTON

ACT-34

FOUR-CHANNEL

TRANSMITTER

The RE-1 includes an Intercom Mode that allows the unit to be operated independent of the Public Switched Network. In this mode, the RE-1 directly supplies the power for the house telephone(s) connected to it.

To use the RE-1 in intercom mode, connect the telephone line as shown under Telephone Wiring Options on Page 6. Note that the RE-1’s Telephone Bypass Module is included in the circuit for additional telephone line surge protection. Be sure the Telephone Bypass Module’s switch is in the NORMAL position.

NOTE: Because there is no connection to the Public Switched Telephone Network, the call forwarding and alternate resident telephone dialing

TOP

BUTTON

	BOTH EQUALS	RIGHT
	TOP BUTTON
		BUTTON
	RIGHT
LEFT
	BUTTON
BUTTON	LEFT
	BUTTON
MDT-2	ACT-22

THREE-CHANNEL

TRANSMITTERS

TOP

BUTTON

	RIGHT
LEFT	BUTTON
BUTTON
BOTTOM-LEFT	BOTTOM-RIGHT
	BUTTON
BUTTON

MDT-4

FIVE-CHANNEL

TRANSMITTER

features will not be available.

This programming step turns the intercom mode on or off. If intercom mode is on, the RE-1 will power the house telephone(s).

If intercom mode is off, the Telephone Company will power the house telephone(s).

Press Intercom Mode

Intercom Mode: 1 = ON; 0 = OFF

21