Linear RE-2 manual Advanced System Programming

Call Forwarding Feature Default: OFF

The call forwarding feature will allow a visitor to contact the resident at the programmed telephone number instead of through the local telephone line. The feature can be set to be active during a selected Time Zone or at all times. The telephone number programmed can contain an extension number and an optional time delay before dialing the extension.

Press: Forwarding Time Zone

Telephone Number Extension Delay

Forwarding: 0 = Call forwarding feature OFF

1 = Call forwarding feature ON at all times

2 = Call forwarding feature ON (scheduled by Time Zone)

3 = Forward the call if there was no resident answer Time Zone = 1-7 (Call forwarding feature active during this Time Zone) Telephone Number = Up to 11-digit telephone number

Extension = Up to 4-digit telephone extension number

Delay = 1-25 seconds (delay between telephone number and extension) Example, call forwarding with only a phone number:

Press: Telephone Number

A special feature is implemented for “Ring Down” PBX systems. If no telephone number is programmed and call forwarding is enabled, the unit will connect immediately without dialing.

Alternate Resident Telephone Numbers Default: All Disabled

For installations where multiple residences exist behind shared controlled access, the RE-2 can dial three alternate telephone numbers. The visitor can call an alternate number by entering “1#”, “2#”, or “3#” on the main keypad.

Press: Location Enable

Telephone Number Extension Delay

Location: 1 = “1#” location; 2 = “2#” location; 3 = “3#” location

Enable: 0 = Disable; 1 = Unconditionally enable

Telephone Number: Up to 11-digit telephone number

Extension: Up to 4-digit telephone extension number

Delay: 1-25 seconds (delay between telephone number and extension)

Resident Response Telephone Keys	Defaults:
	Key A “1” = Activates Relay #1
	Key B “2” = Activates Relay #2

Key C “9” = Disconnect Visitor’s Call

Key D “6” = Switch To/From Call Waiting

The resident response keys are the telephone keys that the resident uses to grant access and control calls from a visitor. The keys for the four functions can be customized. Enter all four keys each time this programming PPN is used.

Press: Keys ABCD

Keys ABCD: Enter 4 digits for the response keys A, B, C, & D Key A = Activates Relay #1

Key B = Activates Relay #2

Key C = Disconnects the Visitor’s Call

Key D = Switches to and from a call holding on call waiting

Resident Programming and Command Prefixes	Defaults:
	Programming = “###”
	Command = “##”

The resident command prefi x is entered on a local telephone prior to entering a command number to control one of the relays or open voice communications with the RE-2. The resident programming prefi x is entered on a local telephone or the main keypad prior to programming the RE-2.

Press: Programming Command

Programming: 0 = “###”; 1 = “***”; 2 = “*#*”; 3 = “#*#” Command: 0 = “##”; 1 = “**”; 2 = “*#”; 3 = “#*”

18

ADVANCED SYSTEM PROGRAMMING

Reset System Defaults

The system can be reset back to the factory defaults with this programming

PPN. EXECUTING THIS PPN WILL NOT ERASE ANY ENTRY CODES OR TRANSMITTERS THAT HAVE BEEN PROGRAMMED.

	Press:
Relay #1 On Time	Default 2: Seconds

Changes the length of time Relay #1 activates when triggered.

Press: Time

Seconds = Output time in seconds 0-60

Relay #2 On Time Default: 2 Seconds

Changes the length of time Relay #2 activates when triggered.

Press: Time

Seconds = Output time in seconds 0-60

Main & Remote Keypad Relay and Time Zone

Default: Main Keypad = Relay #1, No Time Zone Remote Keypad = Disabled

Sets the relay and time zone that the main and remote keypad will use.

Press: Keypad Relay Time Zone

Keypad: 1 = Main Keypad 2 = Remote Keypad (Also see PPN #28)

Relay: 1 = Relay #1 2 = Relay #2

3 = Set by entry code

Time Zone: 0 = no time zone

1-7 to restrict access per time zone 1-7

✦NOTE: To have an entry code select which relay activates, the relay option should be set to “3”.

Relay #2 Alternate Options Default: Access Relay

Relay #2 can be used for functions other than triggering a gate operator or door strike. Relay #2 can be programmed to shunt alarm contacts during Relay #1 activation or perform up to fi ve Alarm Functions. Two PPN numbers are used to program the Relay #2 options.

Press: Role

Role: 0 = Access Relay

1 = Alarm Shunt (Follows Relay #1 activation, used to shunt external alarm contacts with Relay #2’s contacts)

2 = Obstacle Detector

3 = Activate during one or more of the fi ve Alarm Functions programmed below

✦NOTE: More than one alarm function can be enabled at a time. Up to fi ve digits can be entered for “Activate”.

Press: Activate

Activate: 0 = No alarm function (default)

1 = On forced entry (activates when SENSE #1 input opens without Relay #1 activation)

2 = On door/gate ajar (activates when SENSE #1 input stays open for longer than one minute after Relay #1 activation)

3 = On main keypad lockout (activates when the main keypad is in “lockout” from too many incorrect code attempts)

4 = On remote keypad lockout (activates when the remote keypad is in “lockout” from too many incorrect code attempts)

5 = On driveway sensor (activates when SENSE #2 input closes)