| MODEL SLD MECHANICAL PARTS LIST | ||
REF. # | PART # | DESCRIPTION | |
1 | Operator Cover | ||
1A | Plunger Reset Assembly | ||
Plunger Reset Button | |||
| Plunger Extension Only | ||
1B | Lock for Cover, with Keys | ||
Extra Keys | |||
| |||
2 | Main Frame Assembly | ||
2A | Lock Tab Bracket | ||
3 | Bottom Shelf | ||
4 | Pillow Block Tube Spacer | ||
7 | Gear Reducer, 20:1 | ||
7A | Tube Spacers | ||
8 | Reducer Coupler, with Oilite Bushing | ||
10 | Disconnect Collar | ||
11 | Disconnect Collar Spring | ||
12 | Shaft Collar, 1” diameter, 3/8” LTB | ||
13 | Drive Shaft, 1” diameter | ||
13A | 1” Woodruff Key | ||
14 | Disconnect Handle Fulcrum Bracket | ||
15 | Pin for Disconnect Handle | ||
| |||
16 | Disconnect Handle | ||
17 | Disconnect Fulcrum Bracket | ||
18 | Disconnect Lever | ||
19 | Locking Handle Spring | ||
20 | Pillow Block Bearing, 1” diameter | ||
21 | Sprocket, | ||
22 | Sprocket, | ||
23 | #48 Roller Chain, 15 Links | ||
#48 Master Link | |||
| |||
| APeX Module & DC Motor Board Assembly | ||
| APeX Module | ||
24 | APeX DC Motor Board | ||
APeX Mounting Plate | |||
| |||
| Plastic Cover | ||
| Knob Kit | ||
| Limit Box Assembly with Cover | ||
| Limit Shaft | ||
| Oilite Bushing | ||
25 | Limit Nut | ||
1/2” | |||
| Heyco Bushing with Wire Guards | ||
| Limit Switch | ||
| Detent Plate | ||
| Detent Spring | ||
26 | Limit Box Cover | ||
REF. # | PART # |
| DESCRIPTION |
27 |
| Motor, 24 VDC | |
| Brush Replacement Kit | ||
|
| ||
29 |
| Motor Pulley, 2” | |
30 |
| 3” Pulley, 5/8” bore | |
31 |
| ||
32 |
| Alarm | |
33 |
| Stop/Reset Button Bracket | |
34 |
| Stop/Reset Button | |
35 |
| Sprocket, | |
|
| Idler Assembly | |
36 |
| Idler Wheel, UHMW | |
| 1/2” Shoulder Bolt | ||
|
| 1/2” Lock Washer | |
|
| 1/2” Nut | |
37 |
| APeX Controller Mounting Bracket (not shown) | |
|
| Power Box Assembly | |
|
| Power Switch | |
38 |
| Power Outlet | |
| Relay | ||
|
| Bridge Rectifier | |
|
| Fuse Holder | |
|
| Fuse, 10 Amp, | |
39 |
| Transformer Assembly | |
40 |
| Battery Assembly | |
| Battery, 12 Volt (Two required) | ||
|
| Velcro Tape, per Foot | |
41 |
| Accessory Shelf | |
42 |
| Wiring Harness Assembly (not shown) | |
| PARTS FROM ACCESSORY BOX (Not shown in exploded view) | ||
|
| Gate Attachment Bracket | |
|
| ||
|
| #41 Chain Tension Bolt | |
|
| Chain Spring | |
|
| #41 Master Link | |
|
| #41 Chain, per Foot | |
|
| Square Head Bolt, 3/8” | |
|
|
| OPTIONAL PARTS |
|
| Base Plate for Operator | |
|
| Critter Plate | |
|
| Remote Disconnect Kit | |
|
| Post Mounting Kit | |
|
| 2” Torque Limiter Assembly Complete | |
|
| Friction Disc (Pair) | |
|
| 4” Pulley for Torque Limiter | |
|
| Bushing for Pulley | |
SLR • SLC • SLD Slide Gate Operator Installation Guide | - 31 - | 227968 Revision X13 |
