Linear SLD Radio Enable, Antenna Installation, Radio Transmitter Learn, Radio Transmitter Delete

Advanced Controller Programming (Cont.)

Radio Enable

The Controller contains a built-in MegaCode® radio receiver to allow activation from up to 40 access control transmitters and two Model MGT (gate edge) transmitters. The factory default enables the internal radio receiver. Alternately, the internal receiver can be disabled.

Antenna Installation

The Controller is supplied with a local whip antenna installed. If using a remote antenna, remove the whip antenna and connect coax cable from the antenna to the ANTENNA connector.

FUNCTION

"RA"

RADIO

ENABLE

OPTIONS

INTERNAL RADIO RECEIVER DISABLED

INTERNAL RADIO RECEIVER ENABLED

PRESS UP OR

DOWN TO CYCLE

THROUGH OPTIONS

PRESS ENTER TO

SELECT AN OPTION

Radio Transmitter Learn

The Controller’s built-in MegaCode® radio receiver can store the IDs of up to 40 transmitters. Refer to the figure for the steps required to learn transmitters.

✓NOTE: This function will NOT be displayed if the transmitter memory is full, or if the radio receiver is disabled.

Radio Transmitter Delete

Transmitters can be deleted from the Controller’s memory either individually, or all at the same time. Refer to the figure for the steps required to delete transmitters.

✓NOTE: This function will NOT be displayed if no transmitters are stored in memory, or if the radio receiver is disabled.

FUNCTION

"TL"

LEARN

TRANSMITTERS

ENTER	PRESS ENTER (ONCE FOR EACH TRANSMITTER,
	UP TO 40 TRANSMITTERS TOTAL)

"TL" WILL BLINK FOR 30 SECONDS WHILE THE CONTROLLER IS READY TO LEARN A TRANSMITTER

ACTIVATE THE TRANSMITTER

DISPLAY WILL SHOW "- -" THEN THE TRANSMITTER ID NUMBER - IF TRANSMITTER IS ALREADY ENTERED, "dU" WILL BE DISPLAYED, IF DECODE IS BAD "ERROR" WILL BE DISPLAYED

MGT Obstacle Transmitter Learn

The Controller supports one or two Model MGT Obstacle Transmitters. The transmitters can be programmed to function as Open Obstruction, Close Obstruction, Reverse, or Stop. Refer to the figure for the steps required to learn MGT transmitters.

✓NOTE: This function will NOT be displayed if two MGT transmitters are already stored in memory, or if the radio receiver is disabled.

MGT Obstacle Transmitter Delete

MGT transmitters can be deleted from the Controller’s memory either individually, or all at the same time. Refer to the figure for the steps

FUNCTION
		ENTER	PRESS ENTER
	"TD"		"TD" WILL BLINK FOR 30 SECONDS WHILE THE CONTROLLER
			IS READY TO DELETE ONE OR MORE TRANSMITTERS,
			(TO EXIT WITHOUT DELETING ANY, PRESS ENTER)
		ENTER	TO DELETE ALL TRANSMITTERS, PRESS ENTER FOR
			2 SECONDS, OR TO PICK TRANSMITTERS GO TO NEXT STEP
			PRESS UP OR DOWN TO SCROLL THROUGH THE LIST
	UP OR DOWN
			OF TRANSMITTER ID NUMBERS
			THE TRANSMITTER ID NUMBER IS DISPLAYED
			(TO EXIT WITHOUT DELETING, PRESS ENTER)
			(TO PICK A DIFFERENT TRANSMITTER ID, PRESS UP OR DOWN)
DELETE			PRESS ENTER FOR 2 SECONDS TO DELETE THE
		ENTER

TRANSMITTERS TRANSMITTER DISPLAYED

required to delete MGT transmitters.

✓NOTE: This function will NOT be displayed if no MGT transmitters are stored in memory, or if the radio receiver is disabled.

Reset Controller to Factory Defaults

The Controller can be reset with this function. ALL PROGRAMMED DATA WILL BE LOST, and the factory defaults will be loaded. This function will not erase radio transmitters. Transmitters must be deleted with the two functions above.

FUNCTION

ENTER

"ML"

UP OR DOWN

ENTER

LEARN MGT

TRANSMITTERS

PRESS ENTER, "ML" WILL BLINK FOR 30 SECONDS WHILE THE CONTROLLER IS READY TO LEARN AN MGT TRANSMITTER

ACTIVATE THE MGT TRANSMITTER, THE DISPLAY WILL FLASH "rE" - IF THE TRANSMITTER IS ALREADY ENTERED, "DU" WILL BE DISPLAYED, IF DECODE IS BAD "ERROR" WILL BE DISPLAYED

PRESS UP OR DOWN TO SELECT THE MGT FUNCTION: "rE" = REVERSE "St" = STOP

"OP" = OPEN OBSTRUCTION "CL" = CLOSE OBSTRUCTION PRESS ENTER TO ACCEPT THE SELECTION

DISPLAY WILL SHOW "--" FOR 5 SECONDS, THEN SHOW THE TRANSMITTER'S ID NUMBER - REPEAT STEPS FOR SECOND MGT TRANSMITTER IF USED

	FUNCTION						FUNCTION
			ENTER WHILE "CL" IS DISPLAYED, PRESS ENTER						ENTER	PRESS ENTER
		"CL"						"MD"
			ALL PROGRAMMED DATA WILL BE CLEARED							"MD" WILL BLINK FOR 30 SECONDS WHILE THE CONTROLLER
			AND THE FACTORY DEFAULTS WILL BE							IS READY TO DELETE ALL MGT TRANSMITTERS
			STORED IN MEMORY.
			NOTE: THIS FUNCTION WILL NOT ERASE							TO DELETE ALL MGT TRANSMITTERS, PRESS ENTER FOR
									ENTER
										2 SECONDS, (TO EXIT WITHOUT DELETING ANY, QUICKLY
			TRANSMITTERS							PRESS ENTER)
			DEFAULT MOTOR TYPE IS AC, CHANGE
	RESET TO						ERASE MGT			THE DISPLAY WILL SHOW "DELETE ALL" AND THE
			MOTOR TYPE (MO) TO D2 IF USING SLD
FACTORY DEFAULTS							TRANSMITTERS			CONTROLLER RETURNS TO PROGRAMMING MODE
					16
SLR • SLC • SLD			Slide Gate Operator Installation Guide	-		-				227968 Revision X13 2-3-09