Advanced Controller Programming (Cont.)
Auxiliary Relay Mode
The Auxiliary Relay has normally open and normally closed contacts. The factory setting disables the Auxiliary Relay. The relay can be set for:
• Maglock: The relay will energize during any pending or actual gate |
motion (open only), to deactivate a magnetic or solenoid gate lock. |
• Ticket Dispenser: The relay will energize while the gate is moving |
in the open direction and at the full open limit, or in an entrapment |
condition. |
• Strobe: The relay will energize during any pending or actual gate |
motion (either open or close), to activate a warning strobe light. |
• Alarm: The relay will energize if the gate is manually forced open |
from the full closed position. |
FUNCTION
"AR"
PRESS UP OR
DOWN TO CYCLE
THROUGH OPTIONS
PRESS ENTER TO
SELECT AN OPTION
AUXILIARY
RELAY MODE
OPTIONS
AUXILIARY RELAY DISABLED
AUXILIARY RELAY USED FOR
MAGLOCK CONTROL
AUXILIARY RELAY USED FOR
TICKET DISPENSER CONTROL
AUXILIARY RELAY USED FOR
WARNING STROBE LIGHT
AUXILIARY RELAY USED FOR
CONNECTION TO ALARM DEVICE
Reverse Delay Time
The factory default sets the Reverse Delay to 1 second. The operator will wait the length of the delay before reversing direction. This feature will not change the reversal time when the operator is responding to an entrapment condition from an obstruction input or inherent entrapment protection sensor. The Reverse Delay can be set from 1 to 9 seconds. Heaver gates require a longer delay to allow time for the gate to stop.
Low Power Mode
This function is only used with DC slide gate Model SLD. The factory default disables the Low Power Mode.When Low Power Mode is enabled,
FUNCTION
"RD"
REVERSE
DELAY TIME
OPTIONS
SET TIMER VALUE 1 TO 9 SECONDS
PRESS UP OR
DOWN TO CYCLE
THROUGH OPTIONS
PRESS ENTER TO
SELECT AN OPTION
and AC power fails, the controller will assume Low Power Mode after 60 seconds of gate inactivity. Low power mode turns off all accessory power and indicators. Only inputs from the radio receiver, reverse loop, or restoring AC power will wake the Controller from Low Power Mode. Programming Mode can still be accessed while the Controller is in Low Power Mode.
✓NOTE: This function will only be displayed in Model SLD operators.
Power Failure Mode
This function is only used with DC slide gate Model SLD. The factory default is set for Fail Safe, alternately the Controller can be set for Fail Secure, Open Immediate, or Close Immediate.
| FUNCTION |
| OPTIONS |
| |||||
|
|
|
| "LP" |
|
|
| LOW POWER MODE DISABLED | |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| LOW POWER MODE ENABLED | |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| PRESS UP OR |
| |||
|
|
|
|
| DOWN TO CYCLE |
| |||
|
|
|
|
| THROUGH OPTIONS |
| |||
|
|
|
|
|
|
|
|
|
|
| LOW POWER | PRESS ENTER TO | DC MODELS | ||||||
|
| MODE | SELECT AN OPTION | ONLY | |||||
|
|
|
|
|
| ||||
•Fail Safe: If the AC power fails and the battery voltage drops below approximately 22 Volts, 5 seconds later the operator will cycle open if not already open. When AC power is restored, or the battery gets charged by solar panels, the operator will resume normal operation and auto‑close if programmed to do so.
•Fail Secure: If the AC power fails and the battery voltage drops below approximately 22 Volts, 5 seconds later the operator will cycle closed if not already closed. When AC power is restored, or the battery gets charged by solar panels, the operator will resume normal operation.
✓NOTE: Fail Safe and Fail Secure are disabled if Stagger Mode is enabled.
•Open Immediate: If the AC power fails, the operator will cycle open if not already open and cease operation. When AC power is restored, the operator will resume normal operation and
•Close Immediate: If the AC power fails, the operator will cycle closed if not already closed and cease operation. When AC power is restored, the operator will resume normal operation.
✓NOTE: This function will only be displayed in Model SLD operators.
FUNCTION
"FS"
PRESS UP OR
DOWN TO CYCLE
THROUGH OPTIONS
PRESS ENTER TO SELECT AN OPTION
POWER
FAILURE MODE
OPTIONS
SET TO FAIL SAFE MODE
SET TO FAIL SECURE MODE
SET TO OPEN IMMEDIATE MODE
SET TO CLOSE | DC MODELS |
IMMEDIATE MODE | ONLY |
|
SLR • SLC • SLD Slide Gate Operator Installation Guide | - 14 - | 227968 Revision X13 |
