Marantz PM-11S3 NnError messages, NnAre the connections correct?, Symptom Cause Countermeasure

ENGLISH

Troubleshooting

nnError messages

When multiple amplifiers are connected by F.C.B.S., the error messages described in the table below may be displayed on the display. In such a case, ID number setting or remote cable connection may be in failure. Check the ID number or remote cable connection, referring to the table below. For details on ID number setting, see “How to set ID number for F.C.B.S.” (vpage 15).

	Indication			Meaning
1	ERROR 02	Multiple amplifiers take ID					No.	2.
2	ERROR 03	Multiple amplifiers take ID					No.	3.
3	ERROR 04	Multiple amplifiers take ID					No.	4.
! Assign different ID numbers to the amplifiers.
4	ERROR 11	The	amplifiers	with	ID	Nos.		2-4	cannot
		communicate with the amplifier							with ID
		No. 1.
! If the amplifier		with ID No. 1 is		not	on, turn it			ON.
! Check that the remote cable is properly connected.
5	ERROR 12	The	amplifier	with	ID		No.	1	cannot
		communicate with the amplifiers							with ID
		Nos. 2-4.
! If multiple amplifiers take ID				No.	1,	set ID numbers
	properly.
! If the amplifier		with ID No. 1 is connected to the amplifier
	with ID No. 0, set ID numbers properly.

! Check that the remote cable is properly connected.

nnAre the connections correct?

nnIs the unit being operated as described in the owner’s manual? nnAre the other components operating properly?

If this unit does not operate properly, check the items listed in the table below. If the problem persist there may be a malfunction. In that case, disconnect the power immediately and contact your retail outlet.

Symptom

Cause

Countermeasure

Page

When the power is turned

• The

power cord’s plug is

not

fully

• Check the cord is securely inserted into

10

on, the power indicator does

plugged in.

the unit’s AC inlet and the wall power

not light and no sound is

outlet.

produced.

Power switches off suddenly

• The protection circuit will be activated

• Please switch off power at once, and

7

while you are using the unit,

depending upon the temperature rise in

re-apply the power after the body

the

power

indicator

will

the internal parts of the unit.

temperature has fallen sufficiently.

flash

in red

at intervals

of

• Please re-install the

unit in

a place

2

approximately 2 seconds.

having good ventilation.

Power switches off suddenly

• A speaker with impedance

not

• Please use speakers

which

have the

7

while you are using the

supported by this unit is used.

specified impedance.

7

unit,

the

power indicator

• The protection circuit has been activated

• Unplug the power

cord, then after

will flash

red

at intervals

of

because the core wires of different

twisting the core wires together

approximately 0.5 seconds.

speaker cables have touched each other

tightly again, or effecting termination

or a core wire was slipped out of the

treatments etc, please reconnect once

terminal and is touching the unit’s rear

again.

panel.

Even

applying power,

the

• The amplifier circuit in failure.

• Switch off the power and please contact

–

power display flashes red at

the marantz service adviser.

intervals of approximately 0.5

seconds.

The

power

indicator lights

• The

speaker

cables

are

not

fully

• Connect securely.

7

but no sound is produced.

connected.

• Insure the correct input is selected.

11

• The device you want to listen to has not

been selected.

• Set to an appropriate level.

11

• The volume control is set to minimum.

• The input cable is not fully connected.

• Connect securely.

9

• The speaker output switch is set to OFF.

• Set the speaker output switch to ON.

11

Sound is only produced from

• The

speaker

cables

are

not

fully

• Connect securely.

7

the left or right speaker (s).

connected.

• The input cable is not fully connected.

• Connect securely.

9

• The left/right balance is off.

• Adjust to a proper balance

with the

12

balance control knob.

22