SVENSKA | NEDERLANDS | ESPAÑOL | ITALIANO | FRANÇAIS | DEUTSCH | ENGLISH |
Error messages
An error message is displayed if Audyssey® Auto Setup could not be completed due to speaker placement, the measurement environment, etc.
If this happens, check the relevant items, be sure to take the necessary measures, then perform Audyssey Auto Setup over again.
NOTE
Be sure to turn off the power before checking speaker connections.
Simple version
Examples | Error details | Measures |
AUTO SETUP |
| • The connected setup microphone is broken, | • Connect the included setup microphone to | |
AUDYSSEY AUTO SETUP | MultEQ | or a device other than the supplied setup | the SETUP MIC jack of this unit. | |
| Caution! |
| microphone is connected. |
|
| No microphone or Speaker | • Not all speakers could be detected. |
| |
|
|
|
| |
|
|
| • The front L speaker was not properly | • Check the speaker connections. |
|
|
| detected. |
|
| Retry |
|
|
|
Check cause of problem! | RETURN Cancel |
|
| |
|
|
| ||
AUTO SETUP |
| • There is too much noise in the room for | • Either turn off any device generating noise | |
AUDYSSEY AUTO SETUP | MultEQ | accurate measurements to be made. | or move it away. | |
| Caution! |
|
| • Perform again when the surroundings are |
| Ambient noise is too high |
| quieter. | |
| or Level is too low |
|
| |
|
|
| • Speaker or subwoofer sound is too low for | • Check the speaker installation and the |
|
|
| accurate measurements to be made. | direction in which the speakers are facing. |
| Retry |
|
| • Adjust the subwoofer’s volume. |
|
|
|
| |
Check cause of problem! | RETURN Cancel |
|
| |
|
|
| ||
AUTO SETUP |
| • The displayed speaker could not be detected. • Check the connections of the displayed | ||
AUDYSSEY AUTO SETUP | MultEQ |
| speaker. | |
Caution! |
|
|
| |
Front R | None |
|
|
|
Retry |
|
|
|
|
Check cause of problem! | RETURN Cancel |
|
| |
|
|
| ||
AUTO SETUP |
| • The displayed is connected with the | • Check the polarities of the displayed | |
AUDYSSEY AUTO SETUP | MultEQ | polarities reversed. | speaker. | |
Caution! |
|
| • For some speakers, this error message may | |
Front L | Phase |
|
| be displayed even if the speaker is properly |
|
|
|
| |
|
|
|
| connected. If you are sure the connection is |
|
|
|
| correct, press ui to select “Skip”, then |
Retry |
|
|
| press ENTER. |
|
|
|
| |
Skip |
|
|
|
|
Check cause of problem! | RETURN Cancel |
|
| |
|
|
|
AUTO SETUP |
PARAMETER CHECK |
Speaker Config Check
Distance Check
Channel Level Check
Crossover Check
EQ Check
Restore
Show speaker configuration result
| Check the speaker configuration. | |
Speaker Config. Check | ||
| ||
| Check the distance. | |
Distance Check | ||
| ||
| Check the channel level. | |
Channel Level Check | ||
| ||
| Check the crossover frequency. | |
Crossover Check | ||
| ||
| Check the equalizer. | |
EQ Check | ||
|
•If “EQ Check” is selected in step 2, press ui to select equalizing curve (“Audyssey” or “Audyssey Flat”) to be checked.
Use o p to switch the display between the different speakers.
3 Press RETURN.
The confirmation screen reappears. Repeat steps 2.
Retrieving Audyssey Auto Setup settings
If you set “Restore” to “Yes”, you can return to Audyssey Auto Setup measurement result (value calculated at the start by MultEQ®) even when you have changed each setting manually.
Basic version
Advanced version
Information
Remote control operation | Move the cursor | Confirm the setting | Return to previous menu | 11 |
buttons | (Up/Down/Left/Right) |
| ||
|
|
|