Marantz SR6005 manual NnTone, Setting items Setting details Height Gain

	SVENSKA	NEDERLANDS
Setting items	Setting details
Height Gain	Low : Reduce the front height channel volume.
Control the front height	Mid : Front height channel sound is output with standard sound volume.
channel volume.	High : Increase the front height channel volume.
	NOTE
	“Height Gain” is displayed for the following settings.
	• When “Amp Assign” (vpage 61) is set to “Normal”.
	• When the “Speaker Config.” – “F.Height” setting (vpage 62) is set
	other than to “None”.
	• When surround mode is “PLgz” or the PLgz decoder is used.
Default	Yes : Reset to the defaults.
The “Surround Parameter”	No : Do not reset to the defaults.
settings are returned to the
default settings.
nnTone	Default settings are underlined.

Adjust the tonal quality of the sound.

Setting items	Setting details
Tone Control	ON : Allow tone adjustment (bass, treble).

Set the tone control function OFF : Playback without tone adjustment.
to ON and OFF.	“Tone Control” can be set when “Dynamic EQ” (vpage 58) is set to
	“OFF”.

NOTE

•“Tone Control” settings are not reflected to ZONE2.

•The tone cannot be adjusted in the direct mode.

Bass	–6dB – +6dB
Adjust low frequency range	“Bass” can be set when “Tone Control” is set to “ON”.
(bass).
Treble	–6dB – +6dB
Adjust high frequency range	“Treble” can be set when “Tone Control” is set to “ON”.
(treble).

ESPAÑOL	ITALIANO	FRANÇAIS	DEUTSCH	ENGLISH
				Audio/Video Adjust
nnAudyssey Settings			Default settings are underlined.

Set MultEQ®, Dynamic EQ® and Dynamic Volume®. These can be selected after Audyssey® Auto Setup has been performed. For additional information on Audyssey technology, please see page 88.

NOTE

If you have not performed Auto Setup, or if you change the speaker settings after performing Auto Setup, you may not be able to select Dynamic EQ/Dynamic Volume, and “Run Audyssey” may be displayed.

In this case, either perform Audyssey Auto Setup over again or perform “Restore” (vpage 11) to return to the settings after Audyssey Auto Setup was run.

Setting items	Setting details
MultEQ	Audyssey : Optimize the frequency response of all speakers.
Select one equalizer from	Audyssey Byp.L/R : Optimize frequency response of speakers except
three modes. MultEQ	front L and R speakers.
corrects both time and	Audyssey Flat : Optimize frequency response of all speakers to flat
frequency response	response.
problems in the listening	Manual : Apply frequency response set with “Manual EQ” (vpage 59).
area based on Audyssey	OFF : Turn “MultEQ” equalizer off.
Auto Setup calibration. We
recommend “Audyssey”.	• “Audyssey”, “Audyssey Byp. L/R” and “Audyssey Flat” can be
MultEQ is the prerequisite
	selected after Audyssey Auto Setup has been performed. “Audyssey”
function for Dynamic EQ
	is automatically selected after performing Audyssey Auto Setup. When
and Dynamic Volume.
	“Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is selected,
	illuminates.

• After running Audyssey Auto Setup, if the Speaker Configuration, Distance, Channel Level, and Crossover Frequency have changed without increasing the number of speakers

measured, only illuminates.

• Press MULTEQ on the remote control unit to set this setting.

NOTE

•“MultEQ” and “Manual” cannot be selected when “EQ Customize” is set to “Not Used” (vpage 64).

•When using headphones, “MultEQ” is automatically set to “OFF”.

Simple version

Basic version

Advanced version

Information

Remote control operation	Move the cursor	Confirm the setting	Return to previous menu	57
buttons	(Up/Down/Left/Right)