BASIC OPERATION |
(Using the remote control unit)
DIRECT FREQUENCY CALL | (FM) TUNING MODE (AUTO STEREO OR MONO) |
ENGLISH | (TUNER) | |
To operate the unit from the remote control, press | ||
| ||
| the TUNER button on the remote control so that | |
| the tuner mode is engaged. |
LISTENING TO THE TUNER
1. To select tuner and desired band (FM or AM), press the TUNER button twice within two seconds on the remote.
2. Press the > button until PAGE2 is displayed.
3. Press and hold the SCAN+ (D1) or SCAN– (D2) button for 1 second or more.
4. Automatic searching begins then stops when a station is tuned in.
PREV |
| LIP.SYNC | MUTE | 2. |
|
| |||
|
| GUIDEGUIDE |
| |
MENU |
|
| EXIT | |
TEST |
| CH.SEL | SURR |
|
11 |
| 22 | 33 | MODE |
7.1CH |
| ATT | 3. | |
44 |
| 55 | 66 | |
DISP |
| OSD | SLEEP | |
77 |
| 88 | 99 |
|
|
| THX |
|
|
CLEAR |
| 00 | MEMO | R |
TUNERTUNER | CD | MD |
|
|
| VOLUME |
|
|
DOWN |
| UP |
|
|
|
|
| PAGE 1 |
|
|
| AUX 1 INPUT |
|
|
DIGITAL | VIDEO L AUDIO R |
|
| |
|
| CH |
|
|
|
| TV | DVD | VCR |
TUNERTUNER CD
M
D1
D2
D3
D4D4
D5D5
VOL
DSS
MD
Frequency scan step for AM is selectable. Default setup is 9 kHz step, if your country’s standard is 10 kHz step, Press TUNER button on the remote more than 6 seconds. Scan step will
If tuning does not stop at the desired station, use to the “Manual tuning” operation.
MANUAL TUNING
TAPE | AUX1 | AUX2 | AMP | 1. |
|
| LIGHT |
| |
1 |
|
| 2 |
|
RC8500SR
Learning Remote Controller
TAPE | AUX1 | AUX2 | AMP |
When in the auto stereo mode, AUTO indicator will be illuminated on the display.
The “ST” indicator is illuminsted when a stereo
change.
Note:
•Preset memory for the tuner will clear by changing this setup.
AUTO TUNING
2.1.
SOURCE
M
D1
D2
D3
D4
PAGE 2
D5
3.
3.
2.
1. To select tuner and desired band (FM or AM), press the TUNER button twice within two seconds on the remote.
2. Press the GUIDE on the remote, display will show “FREQ - - -
3. Input your desired station’s frequency with the
broadcast is tuned in.
At open frequencies, the noise is muted and the “TUNED” and “ST” indicators are not illuminated. If the signal is weak, it may be difficult to tune into the station in stereo. In such a case, press the MODE button on the front panel.Or press the TUNER button and press the > button until PAGE1
2.1.
SOURCE
M
D1
D2
D3
D4
PAGE 2
D5
3.
3.
2.
ENTER
TUNER CD
TAPE | AUX1 | AUX2 | AMP |
|
| LIGHT |
|
1 |
|
| 2 |
RC8500SR
Learning Remote Controller
1.
ten numbered keypad on the remote.
4.
is displayed. Press the T-MODE (D4) button.
“AUTO” indicator is not illuminated, if FM stereo broadcasts are received in monaural and the “ST” indicator is not illuminated.
To return to auto stereo mode, press the MODE button or press
ENTER
TUNER CD
TAPE | AUX1 | AUX2 | AMP |
|
| LIGHT |
|
1 |
|
| 2 |
RC8500SR
Learning Remote Controller
1.
(Using the SR7500)
1. | To select tuner and desired band (FM or AM), |
2. | press the BAND button on the front panel |
Press the or cursor buttons on the front |
panel to select the desired station.
again. AUTO indicator is illuminated the display.
(Using the SR7500)
1. To select tuner and desired band (FM or AM), press the BAND button on the front panel.
2. Press the 
or
cursor buttons on the front panel for more than 1 second to start the auto tuning function.
3. Automatic searching begins then stops when a station is tuned in.
(Using the remote control unit)
1. To select tuner and desired band (FM or AM), press the TUNER button twice within two seconds on the remote.
2. Press the > button until PAGE2 is displayed
3. Press the SCAN+ (D1) or SCAN– (D2) button to tune in the deseired station.
32
