ENGLISH | REMOTE CONTROL RANGE |
The distance between the transmitter of the | |
remote control and the IR SENSOR of the SR7500 | |
should be less than 5 meters. If the remote control | |
is pointed in a direction other than the IR SENSOR |
3. Close the cover until it clicks.
BATTERY REPLACEMENT INTERVAL
Under normal usage, alkaline batteries last approximately four months. When the batteries wear out, a battery mark is displayed on the LCD. Although the remote control can still be used when
SETTING THE TIME
Example: Setting to 6:20PM (18:20)
12
or if there is an obstacle between them, use of the |
remote control may not be possible. |
|
SR7500 |
60°
CAUTIONS ON BATTERIES
• | Use “AAA” type batteries in this remote control |
| unit. |
• If the remote control unit does not operate from | |
| close to the main unit, replace the batteries with |
| new ones, even if less then a year has passed. |
• | The included battery is only for verifying |
| operation. Replace it with a new battery as soon |
the battery mark is displayed, the batteries should be replaced as soon as possible. The LCD eventually starts to flash when buttons are pressed, the remote control will be unable to transmit signals or learn codes.
•This remote control uses
Reset the clock after replacing the batteries.
Safety Precautions for Batteries
Be sure to always observe the following precautions to prevent fluid leakage, overheating,
POWER
OFF | ON/OFF | ON |
| SOURCE |
|
|
| MM |
|
| D1 |
|
| D2 |
|
| D3 |
|
| D4D4 |
|
| D5D5 |
CH |
| VOL |
| OKOK |
|
| LIP.SYNC |
|
PREV |
| MUTE |
| GUIDE |
|
MENU |
| EXIT |
TEST | CH.SEL | SURR |
11 | 22 | 3 |
7.1CH | ATT | |
4 | 5 | 6 |
DISP | OSD | SLEEP |
7 | 88 | 9 |
3.
3.
2.
6.
4.
5.
USE | PAGE 1 |
3
LEARN
USE | PAGE 1 2 |
4
LEARN
Remote control unit (RC8500SR)
LOADING BATTERIES
The life of the batteries used with the remote control is about 4 months with normal use. Also be sure to replace batteries earlier when you notice that they are getting weak.
1. Remove the back cover.
2. Insert the new batteries (AAA type) with correct and polarity.
| as possible. |
• When inserting the batteries, be careful to do so | |
| in the proper direction, following the + and - |
| marks in the remote control unit’s battery |
| compartment. |
• To prevent damage or battery fluid leakage: | |
| - Do not use a new battery with an old one. |
| - Do not use two different types of batteries. |
| - Do not |
| dispose of batteries in flames. |
• | Remove the batteries when not planning to use |
| the remote control unit for a long period of time. |
• If the batteries should leak, carefully wipe off the | |
| fluid from the inside of the battery compartment, |
| then insert new batteries. |
• | When disposing of used batteries, please |
| comply with governmental regulations or |
| environmental public instruction’s rules that |
| apply in your country or area. |
fire, breakage, accidental ingestion, and other accidents.
•If the batteries are left unused for a long period of time, the battery fluid may leak or the batteries may corrode.
•Do not use the batteries in the remote control with the plus and minus polarity reversed.
•Do not attempt to recharge, heat, or disassemble the batteries. Do not put the batteries in a fire.
•Do not use the remote control with old batteries or
•Do not use different types of batteries or mix old and new batteries in the remote control.
•If the remote control is not operating properly, replace the batteries with new ones.
•If any of the batteries are leaking, completely wipe up all leaked battery fluid, and then replace the batteries with new ones.
| THX |
|
| 5 | 6 |
CLEAR | 00 |
| MEMO | ||
TV | DVD | VCR | DSS |
|
|
TUNER | CD | MD |
|
| |
TAPE | AUX1 | AUX2 | AMP |
| LEARN |
|
| ||||
| LIGHT |
|
|
|
|
1 |
|
| 2 |
|
|
| RC8500SR |
|
|
|
|
| Learning Remote Controller |
|
|
| |
USE | PAGE 1 2 |
When you bought this remote control and insert the batteries to the remote control at first, the steps 1 to 3 are skipped.
Starts from step 4 to set the time.
1. Hold down the M button for three seconds or more.
The menu is displayed.
2. Press the > button once.
This displays second page (SETUP).
3. Press the D4 (CLOCK) direct button.
The “ ” indicator blinks and the clock indicator displays “0:00”.
4. Press the 1 and 8 numeric button to set the
hour indicator.
The hour indicator displays “18”.
The minute indicator blinks “_”.
5. Press the 2 and 0 numeric button to set the
minute indicator.
The minute indicator displays “20”.
The hour indicator blinks.
6. Press the OK cursor button to start the clock.
The clock starts from 0 second at the time that was set and return to normal (USE) mode.
Whenever the batteries are replaced, the clock shows 00:00. Please reset the clock. (The time setting is not backed up.)
10
