Other Function

TV AUTO ON/OFF FUNCTION

This function allows the component connected to the TV-VIDEO in jack to control the power (ON/ OFF) to the SR7500.

ATTENUATION TO ANALOG INPUT

SIGNAL

	LIP.SYNC
PREV		MUTE
	GUIDE
MENU		EXIT
TEST	CH.SEL	SURR

1 2 3

DOLBY HEADPHONE MODE

This feature simulates the waveforms of the actual sounds heard from the speakers.

When headphones are used, the MENU button automatically switches to the Dolby headphone mode.

The OSD that appears when the MENU button is pressed is shown below.

selecting the “VIDEO OFF” setting.

ENGLISH

VIDEO ON/OFF

When no video signal is connected to the SR7500 or a DVD, etc., is connected directly to your TV, the unnecessary video circuit can be turned off by

To select video off, press the AMP button and press the > button until PAGE 4 is displayed. Press the V-OFFbutton.

7.1CH

ATT

SPK-AB

4 5 6

AUTO POWER ON

1. Be sure the TV auto mode is ENABLED. (Refer to page 22: PREFERENCE)

2. Connect your TV TUNER (etc) to the TV- VIDEO in terminal. Be sure to connect the VIDEO input.

3. Turn OFF the power to the TV TUNER and the SR7500.

4. Turn ON the TV TUNER and tune in a receivable station.

5. When the station is received, the SR7500 turns ON and TV is selected automatically.

DISP

OSD

SLEEP

7 8 9

THX

CLEAR0 MEMO

If the selected analog audio input signal is greater than the capable level of internal processing, the “PEAK” indicator will light up on the front display. If this happens, you should press the ATT button on the remote.

“ATT” indicator will be illuminated when this

function is activated. The signal-input level is

reduced by about half. Attenuation will not work

with the output signal of TAPE-OUT, CD-R/MD-

OUT, VCR1-OUT and DSS/VCR2-OUT.

HEAD PHONE

DOLBY HP MODE	: BYPASS
SURROUND	: ✽✽✽
L LEVEL	: 0dB
R LEVEL	: 0dB

DOLDBY HP (Headphone) MODE can be selected with the left and right cursor buttons.

BYPASS → DH1 → DH2 → DH3 → BYPASS

UND RECEIVER SR7500

ENTER

ONES

D4D4

PAGE4

D5D5

CHVOL

TUNER CD CD-R MD

TAPE	AUX1	AUX2	AMPAMP
		LIGHT
1			2

RC8500SR

Learning Remote Controller

AUTO POWER OFF

1. In the above situation, turn the TV TUNER OFF or select a channel that does not contain any broadcast.

2. The power to the SR7500 switches to STANDBY after approx. 5 minutes.

Notes:

• AUTO POWER OFF is canceled if the SR7500 is

set to a source other than TV.

The function reactivates when TV is selected again.

• Some TV broadcasts may cause the TV AUTO

This function is memorized for each individual

input source.

LISTENING THROUGH HEADPHONES

This jack may be used to listen to the SR7500’s output through a pair of headphones. Be certain that the headphones have a standard 1/4” stereo phono plug . (Note that the speakers will automatically be turned off when the headphone jack is in use.)

BYPASS : Bypasses the Dolby headphone mode and delivers ordinary 2-channel stereo.

DH1 : The size of a typical living room space is simulated.

DH2 : The expansiveness of a structure as large as a music hall is simulated.

DH3 : A large space such as that found in a movie theater is simulated.

When the PURE DIRECT mode is selected, Dolby surround processing is bypassed and “✽✽✽” is displayed as the mode indication.

DISPLAY MODE

AV SURROUND RECEIVER SR7500

ENTER

PHONES

	LIP.SYNC
PREV		MUTE
	GUIDE
MENU		EXIT
TEST	CH.SEL	SURR
1	2	3
7.1CH	ATT	SPK-AB
4	5	6
DISPDISP	OSD	SLEEP
77	8	9
	THX
CLEAR	0	MEMO

FUNCTION to turn ON.

• The S-Video terminal does not support “TV

AUTO ON/OFF” function.

AV SURROUND RECEIVER SR7500	The surround mode can be selected when any of
INPUT SELECTOR	the modes in DH1, DH2, or DH3 is selected.
	L/R LEVEL can be set in the ±10 dB range.
	Notes:

You can select the display mode for the front display of the SR7500.

To select this mode, press the DISPLAY on the remote control or the front panel.

When this button is pressed, the display mode is

POWER ON/OFF

PHONES

Note:

•The surround mode returns to the previous setting as soon as the plug is removed from the jack.

•TONE cannot be set when any of the modes in DH1, DH2, or DH3 is selected.

•The Dolby Headphone function will not work when 32 or 96 kHz PCM digital signals are input.

switched in the following sequence.

→Surround Mode → Auto-display Off → Display Off → Input Function → Surround Mode....

In Auto display off mode, the display is off. But, if you make a change to the unit such as input or surround mode, the display will show that change, then go back to off after about 3 seconds. When changing the volume, it is not displayed.

In Display off mode, the display is off completely.

Note:

•Only the DISP indicator will be illuminated on the front display in display off condition.

Marantz SR7500, SR8500 manual Other Function

Models: SR7500 SR8500

OTHER FUNCTION