PRESET MEMORY
MANUAL PRESET MEMORY
RECALLING A PRESET STATION
PRESET SCAN
With this unit you can preset up to 50 FM/AM stations in any order.
For each station, you can memorize the frequency and reception mode if desired.
AUTO PRESET MEMORY
This function automatically scans the FM and AM band and enters all stations with proper signal strength into the memory.
3.2. 4.
DOW
ENTER
DIGI
| S | C |
|
|
PREV |
|
| MUTE |
|
| GUIDE |
|
| |
MENU |
|
| EXIT |
|
TEST | CH.SEL | SURR |
| |
1 | 2 |
| 3 | 3. |
7.1CH | ATT |
| ||
4 | 5 |
| 6 | |
DISP | OSD |
| SLEEP | |
7 | 8 |
| 9 | 2. |
| THX |
|
| |
CLEAR | 0 |
| MEMO | |
|
| |||
TUNER | CD | MD | 1. | |
TAPE | AUX1 | AUX2 | AMP | |
|
| LIGHT |
| |
1 |
|
| 2 |
|
RC8500SR
Learning Remote Controller
(Using the SR7500)
PAGE 2 4
M
D1
D2
D3
D4D4
D5D5 3.
2.
M
D1
D2
D3
D4D4
PAGE 2
D5D5
TUNERTUNER CD
2.
5.
2.
PAGE 2 4
7.1CHATT
4 5
M
D1
D2
D3
D4D4
D5D5
6
2. | 4. 1. 3. | 2. | 5. |
AV SURROUND RECEIVER SR7500 |
|
|
|
(Using the SR7500)
1. Select the desired preset station by pressing the
or
cursor buttons on the front panel
TAPE | AUX1 | AUX2 | AMP |
|
| LIGHT |
|
1 |
|
| 2 |
RC8500SR
Learning Remote Controller
1.
DISPOSD
7 8
THX
CLEARCLEAR0
SLEEP
9
MEMO
4.
5.
| INPUT SELECTOR |
|
| VOLUME |
|
|
| DOWN |
|
| UP |
|
| ENTER |
|
|
|
|
|
|
| AUX 1 INPUT |
|
POWER ON/OFF | PHONES | DIGITAL | VIDEO | L AUDIO R |
1. To select FM , press the BAND button on the front panel.
2. While pressing the MEMORY button, press
the | cursor button. |
“AUTO PRESET” will appear on the display,
and scanning starts from the lowest frequency.
3. Each time the tuner finds a station, scanning will pause and the station will be played for five seconds.
During this time, the following operations are possible.
The band can be changed by the BAND button.
4. If no button is pressed during this period, the current station is memorized in location Preset 02.
If you wish to skip the current station, press the 
cursor button during this period, this station is skipped and auto presetting continues.
5. Operation stops automatically when all 50 preset memory positions are filled or when auto scanning attains the highest end of all bands. If you desire to stop the auto preset memory at anytime, press the CLEAR button.
1. Tune into the radio station you desire (Refer to the “MANUAL TUNING” or “AUTO TUNING” section).
2. Press the MEMORY button on the front panel. “–
3. Select the preset number by pressing the
or
cursor buttons, while this is still blinking (approx. 5 seconds)
4. Press the MEMORY button again to enter. The display stops blinking.
The station is now stored in the specified preset memory location.
(Using the remote control unit)
1. Tune into the radio station you desire (Refer to the “MANUAL TUNING” or “AUTO TUNING” section).
2. Press the MEMO button on the remote. “–
3. Enter the desired preset number by pressing the numeric buttons.
Note:
•When entering a single digit number (2 for example), either input “02” or just input “2” and wait for a few seconds.
(Using the remote control unit)
1. Press the TUNER button twice within two seconds on the remote.
2. Press the > button until PAGE4 is displayed
3. Press the
Or enter the preset station number with the numeric buttons.
(Using the remote control unit)
1. Press the TUNER button twice within two seconds on the remote.
2. Press the > button until PAGE2 is displayed and press the
3. Preset stations are recalled in sequence (No.1
→No.2 → etc.) for 5 seconds each.
No stored preset number will be skipped.
4. You can fast forward the preset stations, press the > button until PAGE4 is displayed and press the
5. When the desired preset station is received, cancel the preset scan operation by pressing the CLEAR button or
33
