MAINTENANCE

FUEL STORAGE

Wood can be dried sufficiently for burning within a few weeks if protected form rain in a low humidity area. It is better to cut wood and allow it to dry for a year. In all cases, the wood should be stacked so that both ends of the sticks are exposed to the air and protected from rain. The drier the wood, the more usable heat produced by the fire and less likely rapid accumulation of soot and creosote within the chimney is to occur. See Chimney Maintenance for information on the hazards of soot and creosote accumulation. Small quantities of wood required for fire tending must be kept at least 30" from the fireplace.

DISPOSAL OF ASHES

Ashes should be placed in a metal container with a tight fit- ting lid. The closed container of ashes should be placed on a noncombustible floor or on the ground well away from all combustible materials until they are finally disposed of. If the ashes are buried or locally dispersed, they should be kept in the closed container until all cinder has thoroughly cooled. Ashes should never be placed in a container with combustible materials.

CHIMNEY MAINTENANCE

Creosote, Formation and Need for Removal

hen wood is burned slowly, it produces tar and other organic vapors which combine with expelled moisture to form creo- sote. The creosote vapors condense in the relatively cool chim- ney flue of a slow-burning fire. As a result, creosote residue accumulates on the flue lining. When ignited, this creosote makes an extremely hot fire.

Note: The chimney should be inspected at least twice a year during the heating season to determine if a creosote buildup has occurred. If creosote has accumulated it should be removed to reduce the risk of a chimney fire.

The chimney cap can be removed for inspection, maintenance and cleaning by removing three screws from the support legs and lifting upward.

When the fireplace is new, inspect the chimney often and clean the chimney any time creosote is seen on the flue walls. Once you see a pattern of how often creosote is accumulating, you can determine how often the chimney should be inspected.

Also changes in the outside environmental conditions such as temperature and humidity or changes in the operation of the fireplace can lead to rapid buildup of soot and/or creosote.

Have a a qualified and reputable chimney sweep clean the chimney or remove creosote or soot with brushes on wooden or fiberglass poles. Note: Do not use metal pipes, chains, wires, etc., to clean the chimney. They can scratch the surface of the stainless steel flue. This will shorten the life of the flue and provide a rough surface for soot particles to attach to.

Be sure to cover nearby furnishing and arrange some method of catching soot and creosote particles that may fall during the chimney cleaning process. If glass doors are installed on the fireplace, they should be closed. Extra caution must be used to avoid damage to the flue damper during the cleaning process.

In addition to checking and cleaning the chimney on a regular basis, be sure to inspect the chimney before starting a fire at the beginning of each heating season. Make sure the chimney is clear from any accumulation of soot, creosote or any other debris. Make sure all joints are intact.

Martin Hearth and Heating does not recommend chemical cleaners because some may contain elements that corrode the metal parts of the chimney or fireplace.

FIREPLACE MAINTENANCE

At the end of each heating season or when the fireplace will not be in use for an extended time, the ashes should be removed and the hearth area should be swept clean. The slow absorption of moisture into the ashes over a long period of time could corrode metal fireplace parts.

At the beginning of each heating season, always operate the flue damper and make sure it has not become stuck from soot, creosote, etc.

Keep the lower and upper grille panels clean and free from dirt and lint accumulation at all times to get the maximum efficiency from your fireplace.

As you use the fireplace, expansion and contraction will cause minor cracking of the hearth, back and side refractory mate- rials. This is normal and unavoidable. If the cracks become large enough or parts dislodge and metal behind the refrac- tory is exposed, the refractory panels should be replaced with new panels. Obtain these panels Martin Hearth and Heating fireplace dealer.

GLASS DOOR MAINTENANCE

For glass door maintenance, see instructions provided with the glass doors.

36

61D0008

Page 35 Page 37
Page 36
Image 36
Martin Fireplaces 400BWBIA, 400BWBCIA, 400BWBA, 400BWBCA operating instructions Maintenance
Page 35 Page 37

400BWBCA, 400BWBCIA, 400BWBIA, 400BWBA specifications

Martin Fireplaces has established a reputation for crafting high-quality, innovative heating solutions that seamlessly blend function and style. The models 400BWBCIA, 400BWBA, 400BWBIA, and 400BWBCA showcase the company’s commitment to excellence in design and performance in the realm of modern fireplaces.

One of the standout features of these models is their sleek, contemporary design that fits perfectly in both traditional and modern home settings. The 400BWBCIA and 400BWBA are designed with an emphasis on a clean face appearance, eliminating any visible frames or trim to provide a minimalist aesthetic. This clean design maximizes the viewing area of the fire, creating a striking focal point in any room.

Each model is equipped with advanced technologies that enhance user experience and efficiency. The Martin Fireplaces utilize a high-efficiency wood-burning system, which not only produces ample heat but also ensures that the emissions are minimized. This eco-friendly approach aligns with contemporary standards for sustainability, making the models an excellent choice for environmentally conscious consumers.

The linear burner design found in the 400BWBIA and 400BWBCA models allows for a larger flame presentation, creating a mesmerizing effect. This design also optimizes heat output, ensuring that the warmth spreads evenly throughout the space. Additionally, the inclusion of glass doors ensures that the flames remain contained while still allowing for an unobstructed view.

Safety is another priority for Martin Fireplaces, and these models integrate several features to promote secure operation. The built-in air wash system keeps the glass clean, enhancing visibility of the flames while reducing maintenance efforts. Moreover, the combustion chamber is engineered to ensure a safe, efficient burn, protecting both the user and the environment.

The versatility of installation is another key characteristic. Both the 400BWBCIA and 400BWBA can be installed as direct vent units, allowing for flexible placement in a variety of settings. Meanwhile, the 400BWBIA and 400BWBCA are perfect for builders looking to integrate contemporary fireplaces into their designs without compromising floor space.

In conclusion, Martin Fireplaces’ 400BWBCIA, 400BWBA, 400BWBIA, and 400BWBCA models are exemplary representations of high-efficiency heating solutions that marry design, technology, and safety. With features that enhance both performance and aesthetics, these fireplaces are ideal for any modern home looking to add warmth and sophistication.
Top Page Image Contents