Manuals / Meridian Audio / Computer Equipment / Projector

Meridian Audio D-ILA 1080MF2 operation manual Connecting to Various Devices, Connecting to Devices

Models: D-ILA 1080MF2

1 40

Download 40 pages 19.15 Kb

Page 18

Image 18

Connecting to Various Devices

Connecting to Devices

Before connection, be sure to turn off both the projector and the device to be connected.

Connecting to digital video processors

●Read the manual that is supplied with the digital video processor thoroughly.

●The signal may attenuate and the image may become unstable depending on the DVI cable. Use the high quality DVI cable below 5 m. When using DVI cable above 5 m, use a split system or optical fiber cable.

Right Side of this unit

SYNC	RS-232C	DVI
OUT SERVICE
CONTROL		IN

DVI OUTPUT

DVI Connection Cable (sold separately)

Control from external device

It is possible to control this unit by connecting a computer to the [CONTROL RS-232C] terminal of this unit.

●Please request a connection cable from us if needed.

●For details, please consult your authorized dealer.

Right Side of this unit

SYNC	RS-232C
OUT SERVICE

CONTROL

RS-232C Connection Cable (sold separately) (Cross Cable)

Page 18

Image 18

Meridian Audio D-ILA 1080MF2 operation manual Connecting to Various Devices, Connecting to Devices, Right Side of this unit

Contents

ILA 1080MF2 Machine Noise Information Germany only About the installation placeFCC Information U.S.A. only About burning-in of the D-ILA deviceDo not allow any unqualified person to install the unit Power cordHow To Replace The Fuse Do not cut off the main plug from this equipmentStandard for gauging replacement time of components Contents AccessoriesControls and Features Front Side/Top Surface/Left SideRear Side/Right Side/Bottom Surface Sync OUT Terminal RS-232C Terminal D-sub 9 Pin Connector PanelService Terminal DVI Terminal DVI-D 24 PinControl Panel Indicator Display on the Control Panel Remote Control Open the back cover Loading Batteries into the Remote ControlPrecautions for Using Batteries Load the batteriesPrecaution for Usage Installing the ProjectorInstallation Environment Adjusting the InclinationProjector and Screen Installation Precautions for Ceiling-mountMounting this Unit Screen Installation Screen Size and Projection DistanceEffective Range of Remote Control Unit When reflecting off a screen When directing remote control unit toward this unit Right Side of this unit Connecting to Various DevicesConnecting to Devices Control from external deviceConnecting the Power Cord supplied When using this unit, remove the lens capAdjusting zoom screen size Basic Operation ProceduresTurning on the power Adjusting focusHiding the image temporarily Turning off the powerPull out the power plug from the power outlet Press HideAdjustments and Settings Using Menus Menu StructureButton Function This Unit Remote Control Unit Menu Operation ButtonsPress the Menu button Press 5/ ∞ to select a main menu item and EnterTo confirm Set up Menu Menu ConfigurationImage adjust Menu Options MenuProject image onto the screen Press 5/∞ to select Set up, followed by pressingScreen Masking Press the Menu buttonPicture Shift Setting Press 5/∞ to select Options, followed by press Ing EnterAbout Lamp Replacement Replacing the LampLight-source Lamp and Lamp Usage Time Insert the new lamp unit until it is fully Loosen the screws on the lamp unit and lift up the handlePull out the lamp unit Tighten the screws of the lamp unit Close the handleTo ensure the lamp time has been reset Resetting Lamp TimeInsert plug into the power outlet ExitCleaning and Replacing the Filter What to do when these messages are displayed Message Cause DetailsPlease follow the procedures below About warning indicatorsIndicator Actions to be taken upon warning indicationsTroubleshooting Pin Arrangement Pin No Signal NameTerminal Description RS-232C TerminalRS-232C External Control External control command table Operation mode Only Asking command is possibleSpecial parameters Specifications Bottom Dimensions Unit mm TopFront SideMF2MIman v0.90ß