Meter Functions | Miller Electric XMT 400 manual

5-2. Meter Functions

.The meters display the actual weld output values for approximately three seconds after the arc is broken.

	Mode		Meter Reading At Idle

			V	A
Scratch Start TIG (GTAW)			80.0	85
		Actual Volts (OCV)		Preset Amps

			V	A
	Lift-Arc TIG		7.5	85
	Lift-Arc TIG
	(GTAW)
	(GTAW)		Blank	Preset Amps



			V	A
	TIG (GTAW)			85
			Blank	Preset Amps

			V	A
	MIG (GMAW)		24.5
	MIG (GMAW)		24.5
			Preset Volts	Blank

			V	A
	Pulsed MIG		PPP	PPP
	Pulsed MIG
	(GMAW-P)
	(GMAW-P)		Pulse Display	Pulse Display
			Pulse Display	Pulse Display

			V	A
	Remote			85
	Remote
	Control SMAW
	Control SMAW		Blank	Preset Amps
			Blank	Preset Amps

			V	A
	SMAW		80.0	85
	Panel Control
		Actual Volts (OCV)		Preset Amps

			V	A
	Voltage-Sensing		80.0
	Voltage-Sensing
	Wirefeeder
	Wirefeeder	Flashes (OCV) And Preset		Blank
		Flashes (OCV) And Preset		Blank

OM-217 769 Page 21

Page 25

Image 25

Miller Electric XMT 400 manual Meter Functions

Contents

Processes OM-217 769LDescription File Multiprocess From Miller to You Table of Contents Page Arc Welding Hazards Symbol UsageElectric Shock can kill HOT Parts can cause severe burns ARC Rays can burn eyes and skin Fumes and Gases can be hazardousWelding can cause fire or explosion Flying Metal or Dirt can injure eyes Fire or Explosion hazard Welding Wire can cause injuryFalling Unit can cause injury Moving Parts can cause injury California Proposition 65 Warnings Principal Safety StandardsEMF Information About Implanted Medical Devices UNE Décharge Électrique peut entraîner la mort Symboles utilisés LES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures gravesLE Soudage peut provoquer un in cendie ou une explosion LES Bouteilles peuvent exploser si elles sont endommagées LE Bruit peut endommager l’ouïeRisque D’INCENDIE OU D’EXPLO- Sion LA Chute DE L’APPAREIL peut blesser LES Fils DE Soudage peuvent provoquer des blessures Proposition californienne 65 AvertissementsLE Soudage À L’ARC risque de provoquer des interférences Information EMF Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-217 769 Manufacturer’s Warning Label Definitions Disconnect input plug or power before working on machineKeep your head out of the fumes 60 s Manufacturer’s Rating Label Symbols And DefinitionsI1max I1eff Duty Cycle And Overheating Specifications CV Mode CC ModeVolt-Ampere Curves Selecting a Location Dimensions And Weight ARC Welding can cause Electromagnetic Interference Weld Output Terminals And Selecting Cable Sizes350 ft 400 ft Put terminals Output Receptacles Remote 14 Receptacle Information Electrical Service Guide To a line terminal For Three-Phase Operation Connecting 3-Phase Input PowerYellow Conductor Select setting best suited for application Power On/Off SwitchFront Panel Controls Inductance/Dig Control Meter Functions Mode Switch Settings Touch Seconds Do not Strike Like a Match Lift-Arc TIG Procedure Blowing Out Inside Of Unit Do not remove case when blowing out inside of unit Voltmeter/Ammeter Help Displays Check, repair, or replace remote control TroubleshootingReset circuit breaker CB1 Remote 14 receptacle − Electrical Diagram − Parts List Dia Part Description Quantity PC3 219 Your distributor also gives ServiceSupport Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s

5-2. Meter Functions

80.0

PPP

80.0

OM-217 769 Page 21