Manuals / Milnor / Laundry Appliance / Clothes Dryer

Milnor manual Kit Instruction KURSPK0025 KURSPK0026, Document ECNs Latest Available

Models: KURSPK0025 KURSPK0026

1 30

Download 30 pages 44.63 Kb

Page 1

Image 1

Published Manual Number/ECN: HURSPK0025/99503N

•Publishing System: TPAS

•Access date: 03/06/03

•Document ECN's: Latest Available

Kit Instruction—

KURSPK0025

KURSPK0026

PELLERIN MILNOR CORPORATION POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.S.A.

Page 1

Image 1

Milnor manual Kit Instruction KURSPK0025 KURSPK0026, Published Manual Number/ECN HURSPK0025/99503N

Contents

Kit Instruction KURSPK0025 KURSPK0026 Publishing System TPAS Access date 03/06/03Published Manual Number/ECN HURSPK0025/99503N Document ECNs Latest AvailableReferences to Yellow Troubleshooting Pages Please ReadAbout the Manual Identifying Information on the Cover Trademarks of Pellerin Milnor CorporationWill Be Damaged If Over-actuated B SETTING LIMIT SWITCHES Limit Switches-Including MicroswitchesLimit Switch Types Inspect switches regularlyWhere Lever or Plunger Should Stop Setting SwitchesRIGHT Plunger Switch AngleÎFree Position of Rotary Lever RIGHTRoller can’t absorb sideways movement of target wrong switch used Roller Plunger Switch AngleRIGHT FIGURE 5 MSSM0116AEspecific warnings, next page and throughout manual PRESS SAFETY FOR INSTALLATION AND SERVICE General Safety RequirementsSafety fence inclosing machine movement areas Local codes may require additional precautionsDanger From Exposed Electrical Components Danger From a Descending Press Main BellNEVER crawl or reach under the press main bell Danger From Moving Conveyor Danger From an Operating PressDO NOT climb on press unless press power is locked OFF and tagged out INSTRUCTIONS INSTRUCTIONS FOR 50 KILO AND 60 KILO PRESS SHIM RETRO-FITHURSPK0026/00186 Page 2 of 19. With the dome in the “down” position, tag and lockout the power10. Manually operate the dome to the up position HURSPK0026/00186 Page 3 of 26. With the dome in the “down” position, tag and lockout the power23. Untag the machine and raise the dome to the “up” position 25. Lower the dome to the “down” positionshaft bearing from the upper cross-member See Figure HURSPK0026/00186 Page 4 of55. Using manual functions, lower the main bell onto the bed 52. Reinstall the diaphragm with the new expansion ring into the dome57. De-energize press power and lock off at main disconnect HURSPK0026/00186 Page 5 ofmeasurements taken in steps 49 and HURSPK0026/00186 Page 6 ofEXAMPLE HURSPK0026/00186 Page 7 of Trace Outline of Main Bell Air Cylinder Base on Upper Cross Member Main Bell Air Cylinder BoltsHURSPK0026/00186 Page 8 of Main Dome Coupling Torque To 25 ft-lb33.9 Nm HURSPK0026/00186 Page 10 of Downlock Shims Placed on Bed in order to Shim Main Bell Air CylinderHURSPK0026/00186 Page 11 of One of the Four Main Bell Air Cylinder BoltsHURSPK0026/00186 Page 12 of Main Bell Air Cylinder ShimsHURSPK0026/00186 Page 13 of Lock Shaft Bearing Right-Hand Side Lock Shaft Bearing Lock Shaft Spacers Left-Hand SideHURSPK0026/00186 Page 14 of HURSPK0026/00186 Page 15 of Right-Hand Side Lock Shaft BearingShaft Lock Upper Cross-MemberUplock Jaw HURSPK0026/00186 Page 16 ofHURSPK0026/00186 Page 17 of HURSPK0026/00186 Page 18 of Old Setup of Dome Full-Up Contact Switch and BracketDome Full-Up Contact Switch Bracket Dome Full-Up Contact Switch New Positioning of Dome Full-Up Contact Switch and BracketHURSPK0026/00186 Page 19 of HURSPK0026/00186 Page 20 of HURSPK0026/00186 Page 21 of Location of Downlock Shims Lock Ring Bolts