Manuals / Milnor / Laundry Appliance / Clothes Dryer

Milnor KURSPK0026, KURSPK0025 manual HURSPK0026/00186

Models: KURSPK0025 KURSPK0026

1 30

Download 30 pages 44.63 Kb

Page 26

Image 26

HURSPK0026/00186

Page 17 of 21

Figure 9

Square Holes in the Side of the Uplock Jaw (File Paint off of the Inside surface of the Holes)

Page 26

Image 26

Milnor KURSPK0026, KURSPK0025 manual HURSPK0026/00186

Contents

Published Manual Number/ECN HURSPK0025/99503N Publishing System TPAS Access date 03/06/03Kit Instruction KURSPK0025 KURSPK0026 Document ECNs Latest AvailableAbout the Manual Identifying Information on the Cover Please ReadReferences to Yellow Troubleshooting Pages Trademarks of Pellerin Milnor CorporationLimit Switch Types B SETTING LIMIT SWITCHES Limit Switches-Including MicroswitchesWill Be Damaged If Over-actuated Inspect switches regularlySetting Switches Where Lever or Plunger Should StopÎFree Position of Rotary Lever Plunger Switch AngleRIGHT RIGHTRIGHT Roller Plunger Switch AngleRoller can’t absorb sideways movement of target wrong switch used FIGURE 5 MSSM0116AESafety fence inclosing machine movement areas PRESS SAFETY FOR INSTALLATION AND SERVICE General Safety Requirementsspecific warnings, next page and throughout manual Local codes may require additional precautionsNEVER crawl or reach under the press main bell Danger From a Descending Press Main BellDanger From Exposed Electrical Components DO NOT climb on press unless press power is locked OFF and tagged out Danger From an Operating PressDanger From Moving Conveyor INSTRUCTIONS FOR 50 KILO AND 60 KILO PRESS SHIM RETRO-FIT INSTRUCTIONS10. Manually operate the dome to the up position 19. With the dome in the “down” position, tag and lockout the powerHURSPK0026/00186 Page 2 of 23. Untag the machine and raise the dome to the “up” position 26. With the dome in the “down” position, tag and lockout the powerHURSPK0026/00186 Page 3 of 25. Lower the dome to the “down” positionHURSPK0026/00186 Page 4 of shaft bearing from the upper cross-member See Figure57. De-energize press power and lock off at main disconnect 52. Reinstall the diaphragm with the new expansion ring into the dome55. Using manual functions, lower the main bell onto the bed HURSPK0026/00186 Page 5 ofEXAMPLE HURSPK0026/00186 Page 6 ofmeasurements taken in steps 49 and HURSPK0026/00186 Page 7 of HURSPK0026/00186 Page 8 of Main Bell Air Cylinder BoltsTrace Outline of Main Bell Air Cylinder Base on Upper Cross Member 33.9 Nm Torque To 25 ft-lbMain Dome Coupling Downlock Shims Placed on Bed in order to Shim Main Bell Air Cylinder HURSPK0026/00186 Page 10 ofOne of the Four Main Bell Air Cylinder Bolts HURSPK0026/00186 Page 11 ofMain Bell Air Cylinder Shims HURSPK0026/00186 Page 12 ofHURSPK0026/00186 Page 13 of HURSPK0026/00186 Page 14 of Right-Hand Side Lock Shaft Bearing Lock Shaft Spacers Left-Hand SideLock Shaft Bearing Right-Hand Side Lock Shaft Bearing HURSPK0026/00186 Page 15 ofUplock Jaw Upper Cross-MemberShaft Lock HURSPK0026/00186 Page 16 ofHURSPK0026/00186 Page 17 of Old Setup of Dome Full-Up Contact Switch and Bracket HURSPK0026/00186 Page 18 ofHURSPK0026/00186 Page 19 of New Positioning of Dome Full-Up Contact Switch and BracketDome Full-Up Contact Switch Bracket Dome Full-Up Contact Switch HURSPK0026/00186 Page 20 of Location of Downlock Shims Lock Ring Bolts HURSPK0026/00186 Page 21 of