< PIP, POP and SIDE BY SIDE >
The following table shows the combination of signal inputs under which the “PIP” and “POP” modes function. These modes do not function, however, when the screen size is “CUSTOM” or “REAL”.
English
SUB | RGB1 | RGB2 | RGB3 | RGB4 | RGB5 | DVD/HD VIDEO<S> VIDEO |
MAIN | (HDMI) |
| (BNC) | (CAT5) | (YPbPr) | |
RGB1 (HDMI) |
|
|
|
|
|
|
RGB2 |
|
|
|
|
|
|
RGB3 |
|
|
|
|
|
|
RGB4 (BNC) |
|
|
|
|
|
|
RGB5 (CAT5) |
|
|
|
|
|
|
DVD/HD (YPbPr) |
|
|
|
|
|
|
VIDEO<S> |
|
|
|
|
|
|
VIDEO |
|
|
|
|
|
|
: Supported
: Not supported
Press the “PIP ON/OFF” buttons on the remote control to change between “PIP”, “POP” and “SIDE BY SIDE” mode as shown in the diagram below.
|
| PIP |
|
| POP |
|
| SIDE BY SIDE |
|
| SIDE BY SIDE |
|
| OFF |
| |||||
|
|
|
|
|
| ASPECT |
|
| FULL |
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
“PIP”, “POP” mode resolution (Reference) |
| |
PIP SIZE | SMALL | : 450 dots X 338 dots |
| MIDDLE | : 675 dots X 450 dots |
| LARGE | : 900 dots X 675 dots |
POP SIZE |
| : 450 dots X 338 dots |
< Supplemental information of the auto brightness function >
To control multiple monitors collectively
In such a case where the tiling function is used, you can control the auto brightness function by sharing the detection result of the brightness sensor of a certain monitor among the connected monitors.
1.
Monitor | Monitor | Monitor |
|
|
ID = 9 | ID = 8 | ID = 7 |
|
|
(Slave) | (Slave) | (Slave) | Master: Monitor configured as Master that detects | |
|
|
|
| the outside light (Monitor ID is “1”.) |
Monitor | Monitor | Monitor | Slave: | Monitor controlled by the Master monitor |
| (Monitor ID is other than “1”.) | |||
ID = 6 | ID = 5 | ID = 4 |
| |
|
| |||
(Slave) | (Slave) | (Slave) |
|
|
Monitor | Monitor | Monitor |
|
|
ID = 3 | ID = 2 | ID = 1 |
|
|
(Slave) | (Slave) | (Master) |
|
|
2.Assign a monitor ID to each
The monitor ID of the Master monitor should be “1” and those of the Slave monitors should be other than “1”. You are recommended to assign IDs to the monitors consecutively from 1, 2, 3, and on.
3.Set AUTO BRIGHTNESS on the OSD screen (PICTURE) as follows.
| AUTO BRIGHTNESS | CONTROL |
Master monitor | LOCAL | PRIMARY |
Slave monitors | REMOTE | SECONDARY |
