Use of the Remote Control with Other A/V Products
Programming the Remote Control to Use with Other Brands of Audio and Video Products:
(Figures 1-3 this page, figures 4-5 following page)
1.Move the slide switch at the top of the remote to the product you want to control.
2.Press and hold the POWER button on the remote control.
3.Enter the first three digit code listed for your equip- ment, and then release the POWER button on the remote control.
4.Point the remote control to the equipment and press the POWER button.
Note: If the equipment responds, the remote control is properly programmed to operate the equipment. If the equipment does not respond, repeat steps 2- 4 with the next three digit code listed in step 3 for your equipment.
IMPORTANT
When set to TV, the PLAY, STOP, REW/REV, and FF/FWD buttons will operate the VCR after the VCR codes have been properly programmed into the remote control.
| CABLE/DBS/DTV |
| VCR | DVD |
| ||||||||||
| TV |
|
|
|
|
|
|
|
|
|
| AUDIO | 2.POWER | ||
|
|
|
|
|
|
|
|
| |||||||
1. |
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| |||||
3. |
|
|
|
|
|
| Cable Box Codes |
| |||||||
| Cable box brand | Code to enter: | If your | ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| cable box |
| General Instruments/ | 119, 120, 121, 122,123, | |||||||||||||
| Jerrold | 124 |
|
|
|
| code is not | ||||||||
|
|
|
|
| listed here, | ||||||||||
| Motorola | 125, 126, 127 | |||||||||||||
| please see | ||||||||||||||
| Oak | 139, 137, 102 | |||||||||||||
| page 48 | ||||||||||||||
| Pioneer | 101, 116 |
| ||||||||||||
|
| for a | |||||||||||||
| Scientific Atlanta | 112, 113 |
| ||||||||||||
|
| complete | |||||||||||||
| Zenith | 117, 100 |
| ||||||||||||
|
| listing. | |||||||||||||
| To reset to default code, enter 000 | ||||||||||||||
|
| ||||||||||||||
Figure 1. Programming the remote to control your cable box. | |||||||||||||||
| CABLE/DBS/DTV |
| VCR | DVD |
| ||||||||||
| TV |
|
|
|
|
|
|
| AUDIO | 2.POWER | |||||
|
|
|
|
|
|
|
| ||||||||
1. |
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| |||
3. |
|
| Satellite | Receiver Codes |
| ||||||||||
| Satellite brand |
| Code to enter: | If your | |||||||||||
| Mitsubishi DTV - DBS |
| 006 |
|
| satellite | |||||||||
| DishNetwork |
| 175 |
|
| receiver | |||||||||
| Hughes - DBS |
| 173 |
|
| code is not | |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| listed here, |
| Panasonic - DBS |
| 174 |
|
| ||||||||||
|
|
|
| please see | |||||||||||
| RCA - DBS |
| 176 |
|
| ||||||||||
|
|
|
| page 49 for | |||||||||||
| Sony - DBS |
| 177 |
|
| ||||||||||
|
|
|
| a complete | |||||||||||
|
| 170, 173, 189, 190, 191 | |||||||||||||
|
| listing. | |||||||||||||
| To reset to default code, enter 000 | ||||||||||||||
|
| ||||||||||||||
Figure 2. Programming the remote to control your satellite receiver.
| CABLE/DBS/DTV |
| VCR | DVD |
| |||||
| TV |
|
|
|
|
|
|
| AUDIO | 2.POWER |
|
|
|
|
|
|
| ||||
1. |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| |||
3. |
|
|
|
|
| VCR Codes |
| |||
| VCR brand | Code to enter: | If your | |||||||
| Mitsubishi | 001, 002 | VCR | |||||||
| Hitachi | 020, 043, 065 | code is not | |||||||
| listed here, | |||||||||
| JVC | 030, 054 | ||||||||
| please see | |||||||||
| Philips / Magnavox | 043, 044, 051 | ||||||||
| page 49 | |||||||||
| Panasonic | 041, 042, 043 | ||||||||
| for a | |||||||||
| RCA | 020, 053, 065 | ||||||||
| complete | |||||||||
| Sony | 048, 049, 050 | ||||||||
| listing. | |||||||||
| Toshiba | 021 |
|
| ||||||
|
|
|
| |||||||
| To reset to default code, enter 000 |
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
Figure 3. Programming the remote to control your VCR.
20 Plasma TV
