Manuals / Mitsubishi Electronics / TV and Video / Projection Television

Mitsubishi Electronics WD-Y57aa manual IR Emitter NetCommand and TV Guide On Screen, TjfeEfwjdft

Models: WD-Y57aa

1 124
Download 124 pages 14.86 Kb
Page 31
Image 31

Chapter 2. TV Connections

31

IR Emitter NetCommand® and TV Guide On Screen

An IR emitter cable is included with the TV.

The NetCommand system uses emitters connected to the IR EMITTER jack to control other devices such as VCRs, DVD players, cable boxes, and satellite receiv- ers. This control system is shared with the TV Guide On Screen system.

1.Connect the plug end of the supplied IR emitter cable to the IR EMITTER NetCommand® jack on the TV back panel.

2.Run the cable for each of the emitter ends under, alongside, or over each device to be controlled so that the emitter end is in front of the area where the remote control sensor is located.

3.Position the emitter end with the emitter bulb facing the remote control sensor. The bulb emits infrared light in a cone-shaped pattern. Place the bulb far enough from the sensor to allow the cone pattern to reach the sensor.

The IR sensor is usually behind the plastic window of the front display panel. It is sometimes visible with the aid of a flashlight and is normally a round or square cutout behind the plastic. If you cannot see the sensor and the device’s Owner’s Guide does not specify the location, you can find it by following these steps using the device’s remote control:

a.Hold the remote about one-half inch from the front of the device. Starting from one end of the display window plastic, press the POWER button.

b.If the device does not respond, move the remote control one inch toward the center and try again.

c.Repeat this until the device responds.

d.Note this location and then start over from the other end of the display window plastic, repeating until the device responds again.

The remote control sensor is somewhere between these two positions. This is usually enough accu- racy for placement of the IR emitters.

With some devices, the emitter works better facing downward from the top of the device. Experiment if needed.

4.Secure the emitter ends in place using double-sided tape.

IMPORTANT

Position IR emitters so that each device’s sensor “sees” the signal from only one emitter. Otherwise, a device receiving signals from multiple sources (remote controls, IR emitters) may not respond at all.

5.Place any unused ends behind the devices to prevent stray signals from reaching the IR sensors.

 

 

"/5"69

"/5."*/ 64&8*5)

 

 

 

$BCMF$"3%



0UIFS"7EFWJDF



 

 

 

 

 

 

 

 

 

R

 

 



$BCMF$"3%™64&8*5)"/5$"3%50

 

 

 

 

 

%*(*5"-

*&&&

 

 

"6%*0

 

 

 

065

 

 

 

57#BDL1BOFM



"73FDFJWFS

 

 

 

 

 

Figure 14. Connecting IR Emitter NetCommand

*3TFOTPS *OGSPOUPGB

TJOHMFBWFSBHF TJ[FEEFWJDF

*3TFOTPS

0OUPQPGBTJOHMF

UBMMEFWJDF

*3TFOTPS

*3TFOTPS *OGSPOUTIBSFE CZUXPBWFSBHF

TJ[FEEFWJDFT

Figure 15. IR emitters so the signal can be “seen” by the IR sensor on each device.

Page 30 Page 32
Page 31
Image 31
Mitsubishi Electronics WD-Y57aa manual IR Emitter NetCommand and TV Guide On Screen, Tfotps *OGspouPgB, TjfeEfwjdft
Page 30 Page 32

WD-Y57aa specifications

The Mitsubishi Electronics WD-Y57AA is a cutting-edge projector designed to redefine the home theater experience. With its advanced features and innovative technologies, this model stands out among its competitors, offering exceptional performance tailored for movie enthusiasts and gamers alike.

One of the most notable features of the WD-Y57AA is its high-definition resolution, which delivers stunning visuals that bring images to life. Whether you're watching your favorite films or playing video games, the clarity and detail provided by this projector make every viewing experience captivating. With a resolution of 1080p, it ensures that even the finest details are rendered sharp and vibrant.

Another impressive characteristic of the WD-Y57AA is its brightness. With an output of 3000 ANSI lumens, the projector can produce bright and vivid images even in moderately lit rooms. This versatility allows users to enjoy the projector in a variety of settings, be it a dedicated home theater or a multifunctional living area.

The projector utilizes DLP technology, known for its reliability and high image quality. DLP ensures that the color reproduction is accurate, which means that reds are rich, greens are vibrant, and blues are deep, providing a well-balanced color palette. Coupled with a dynamic contrast ratio, images can appear more lifelike with enhanced depth and detail in both shadows and highlights.

The projector's connectivity options are another highlight. It is equipped with multiple HDMI ports, allowing users to connect a wide range of devices, from Blu-ray players to gaming consoles. Additionally, the WD-Y57AA supports various video formats and can easily adapt to the latest gaming technologies, making it a future-proof choice for enthusiasts.

User-friendliness is also a key aspect of the WD-Y57AA. The device includes an intuitive interface that simplifies navigation and control, making it easy to adjust settings as needed.

In summary, the Mitsubishi Electronics WD-Y57AA combines high-definition resolution, impressive brightness, and DLP technology to deliver an exceptional viewing experience. With its variety of connectivity options and user-friendly design, this projector is an excellent choice for anyone looking to enhance their entertainment setup.