ENGLISH
Clean the entire machine. It is particularly important to clean under the cutting deck. Touch up paint damage to prevent rust.
Store the machine indoors in a dry place. Machines with an electric starter:
Remove the battery. Store it well charged in a cool place (between 0°C and +15°C).
At the correct storage temperature, the battery should be
The battery acid is extremely corrosive and can cause injuries and damage to skin and clothing. Always use rubber gloves and glasses (goggles) to protect your eyes. Avoid inhaling any acid vapour.
Do not incline the battery too much so that the battery acid can run out onto hands or clothing. If this should happen, rinse with plenty of water.
4 ASSEMBLY
To avoid injury and damage to people and property, do not use the machine until all the measures in this instruction have been carried out..
4.1 Accessories bag
The machine is supplied with a plastic bag contain- ing components which shall be used during the as- sembly. The bag contains (fig. 1):
Pos. No. | Designation | Dimension | |
B |
| Spare key |
|
C | 1 | Tension pin | 6 x 36 |
D | 1 | Shim washer | 16 x 38 x 0.5 |
E | 1 | Shim washer | 16 x 38 x 1.0 |
F | 2 | Shoulder washer |
|
G | 2 | Screw | 8 x 20 |
H | 2 | Screw knob |
|
I | 4 | Washer | 8.4 x 24 x 1.5 |
J | 1 | Drawing plate |
|
K | 4 | Screw | 8 x 20 |
L | 2 | Nut |
|
M2 Screw for battery
N2 Nut for battery
O | 2 | Screw | M10 x 35 |
P | 2 | Nut | M10 |
Supplied installed on the front axles:
Pos No. Designation
Q2 Lock pin
R2 Washer
Secure to the implement lifter:
Pos | No. | Designation |
S | 2 | Deck mount |
10 |
|
|
4.2 Engine casing
To fill with fuel and to inspect and maintain the en- gine and battery, open the engine casing.
The engine must not be running when the casing is opened.
4.2.1Opening
1.Raise the seat lock (fig. 2) and fold the seat for- wards.
2.Pull up the rubber strap at the front edge of the casing (fig. 3).
3.Grasp the front edge of the engine casing and fold up the casing (fig. 4).
4.2.2 Closing
1.Grasp the front edge of the engine casing and fold down the casing (fig. 4).
2.Secure the front edge of the casing with the rub- ber strap (fig. 3).
The machine may not be operated un- less the engine casing is closed and locked. Risk of burns and crushing in- juries.
4.3 Battery
See “8.8 Battery”.
4.4 Seat, fig. 6
Release the catch (S) and fold up the seat bracket. Install the mounting in the rear (upper) holes as follows:
1.Install the shoulder washers (F) on the screws
(K).
2.Insert the screws through the slots in the brack- et. Place a washer (I) between the seat and the bracket.
3.Tighten the screws in the seat. Tightening torque: 9±1.7 Nm.
If the screws are tightened more than 9±1.7 Nm, the seat will be damaged.
4.Check that the seat moves easily in the slots in the bracket.
Install the mounting in the front (lower) holes as follows:
1.Install the screw knobs (H) on the screws (G).
2.Install a washer (I) on each screw.
3.Insert the screws through the slots in the bracket and tighten by hand in the seat.
4.Fold the seat down and place it in the desired position.
5.Tighten the screw knobs (H) by hand.
The screw knobs (H) and the seat will be damaged if tools are used.
