Multiquip HHXG5 SpecificatiOnS (enGine)

HHXg5 RIDe-ON TROWeL • OpeRaTION maNuaL — Rev. #1 (10/25/10) — page 15

SpecificatiOnS (enGine)

Table 2. HHXg5 engine Speciﬁcations

model vanguard Dm950g

Type Gasoline

Cylinders 3

Displacement 58.1 cu.in. (952 cc)

Power

(Maximum Output)

31 HP (23.1 kW) @3600 rpm

Bore and Stroke 2.83 in. x 3.07 (72 mm x 78 mm)

Maximum Torque

(Intermittent)

70.0 Nm @ 2200 rpm

Compression Ratio 8.7 : 1

Cooling System Fully jacketed water-cooled

Engine Oil Capacity

3.2 qt. (3 liters)

3.5 qt. (3.3 liters) w/ oil ﬁlter

replacement

Lubricating System Pressure feed with spin-on ﬁlter

Fuel Tank 9 gal. (34 liters)

Fuel Delivery System Carbureted

Helical Gearbox Gear

Compound Capacity

144 oz. (4.26 liters)

ISO 22O AGMA GR 5EP

Fuel Gasoline - minimum of 87 octane

rating

Starting System Electric Starter

Dry Weight 143.3 lbs. (65 Kg)

Dimensions

(L x W x H)

17.4 in. x 17.1 in. x 19.7 in

(441.8 mm x 443.2 mm x 501.4

mm).

Contents

Main MODel HHXG5 page 2 HHXg5 RIDe-ON TROWeL OpeRaTION maNuaL Rev. #1 (10/25/10) prOpOSitiOn 65 WarninG WARNING SilicOSiS/reSpiratOry WarninGS WARNING SILICOSIS WARNING RESPIRATORY HAZARDS taBle Of cOntentS HHXG5 ride-On trowel Page traininG cHeckliSt TRaININg CHeCKLIST Daily pre-OperatiOn cHeckliSt SaFeTY meSSageS geNeRaL SaFeTY TROWeL SaFeTY eNgINe SaFeTY FueL SaFeTY BaTTeRY SaFeTY TRaNSpORTINg SaFeTY TOWINg SaFeTY eNvIRONmeNTaL SaFeTY DiMenSiOnS/SpecificatiOnS (trOWel) SpecificatiOnS (enGine) (Maximum Output) (L x W x H) (Intermittent) General infOrMatiOn HHX RIDe-ON TROWeL FamILaRIzaTION eNgINe HHXg5 BLaDeS geaRBOXeS Page Page Page enGine cOMpOnentS (GaSOline) Setup TROWeL SeTup INSTRuCTIONS BaTTeRY SeTup inSpectiOn eNgINe OIL LeveL geaRBOX OIL LeveL FueL HYDRauLIC FLuID FILTeR STaRTINg THe eNgINe STeeRINg Blade pitch maINTeNaNCe maINTeNaNCe SCHeDuLe Daily (8-10 Hours) Weekly (30-40 Hours) monthly (100-150 Hours) Yearly (500-600 Hours) air Cleaner (Daily) COVER LATCHES (COVER CLAMPS) Changing engine Oil and Filter AIR CLEANER BODY Oil/Water Separator Oil and Fuel Lines Radiator/Cooling System Battery/Charging System Long Term Storage Lower (Driven) Pulley Removing the Drive Belt Upper (Drive) Pulley Spare Drive Belt Holder Spare Drive Belt Installing the Drive Belt (using New Drive Belt) Fixed Face CV Joint Spread Apart Upper Pulley Drive Belt Spare Drive Belt Replacement CV Joint Bolt Left Side Gearbox New Spare Drive Belt CVT (Drive Pulley) Drive V-Belt Driven Pulley How It Works (Figure 25) Clutch CHeCKINg THe DRIve BeLT BeLT meaSuRemeNT RemOvINg THe DRIve BeLT Lower (Driven) Pulley Upper (Drive) Pulley INSTaLLINg DRIve BeLT HOW IT WORKS Maintenance (trOWel) Blade pitch Single pitch Twin pitch Blade pitch adjustment procedure Maintenance (trOWel) Changing Blades Steering adjustment Clean-up Trowel arm adjustment Trowel Blade Removal Trowel arm Removal Bronze Bushing Spider Plate Pin Checking Trowel arm Straightness D-Shaft Section Trowel arm adjustment Re-assembly Installing pans Onto Finisher Blades Blade Assembly Hydraulic Steering pressure Tie-Down Knob Tie-Down, Blade Interpreting the pressure Reading Z-Clip, Pan Steering pressure adjustment DecOMMiSSiOninG trOWel Decommissioning Trowel/Components WirinG DiaGraM (enGine) CONNECT TO CHASSIS GROUND MODULE F8 50A WirinG DiaGraM (enGine) CONNECT TO CHASSIS GROUND SPARK PLUGS MODULE F8 Troubleshooting (Ride-On Trowel) Symptom possible problem Solution Troubleshooting (Ride-On Trowel) - continued Symptom possible problem Solution Page Page OperatiOn Manual HERES HOW TO GET HELP Your Local Dealer is: pn: 23110 PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING UNITED STATES