Training checklist, Completely | Multiquip HHXG5 instruction

training checklist

TRAINING CHECKLIST

This checklist will lists some of the minimum requirements for machine maintenance and operation. Please feel free to detach it and make copies. Use this checklist whenever a new operator is to be trained or it can be used as a review for more experienced operators.

Training Checklist

No,

Description

OK?

Date

1Read operation manual

completely.

		Machine layout, location of
	2	components, checking of engine
		and hydraulic oil levels.

	3	Fuel system, refueling procedure.

	4	Operation of spray and lights.

	5	Operation of controls (machine
	5	not running).
		not running).

	6	Safety controls, safety stop switch
	6	operation.
		operation.
	7	Emergency stop procedures.

	8	Startup of machine, pre-heat,
	8	engine choke.
		engine choke.

	9	Maintaining a hover.

	10	Maneuvering.

	11	Pitching.

12Matching blade pitch. Twin-Pitch™

13Concrete fi nishing techniques.

14Shutdown of machine.

15Lifting of machine (lift loops).

16Machine transport and storage.

page 6 — HHXg5 RIDE-ON TROWEL • operation manual — rev. #1 (10/25/10)

Image 6

Multiquip HHXG5 operation manual Training checklist, Completely

Contents

Model HHXG5 Proposition 65 Warning Silicosis/Respiratory Warnings Silicosis WarningRespiratory Hazards Table of Contents HHXG5 Ride-On TrowelPage Training checklist Completely Daily pre-operation checklist Daily pre-Operation Checklist Safety Information SaFeTY meSSageS GeNeRaL SaFeTY Order Form PT-160 TROWeL SaFeTYENgINe SaFeTY Before servicing equipment FueL SaFeTY BaTTeRY SaFeTY„ Use well-insulated gloves when picking up the battery Lifting TRaNSpORTINg SaFeTYTOWINg SaFeTY „ aLWaYS shutdown engine before transporting ENvIRONmeNTaL SaFeTY DIMENSIONS/SPECIFICATIONS Trowel HHX Specifications Specifications Engine Fuel General Information Controls and Indicators HHXG5 Controls and Indicators Front HHXG5 Controls and Indicators Rear HHXG5 Controls and Indicators Clamshell Open Engine Components Gasoline Linked to the accelerator system Setup Trowel Setup InstructionsBattery Setup Gearbox Oil Level InspectionEngine Oil Level Fuel Operation Starting the Engine Steering Control Joystick Directional Positioning Blade Pitch Matching Blade Pitch for Both Sets of Blades Weekly 30-40 Hours MAINTENANCEMaintenance Schedule Daily 8-10 Hours Monthly 100-150 Hours Oil Filter 300 Hours Air Cleaner DailyChanging Engine Oil And Filter Fuel Filter Oil And Fuel Lines Battery/Charging SystemOil/Water Separator Radiator/Cooling System MAINTENANCE old style clutch Checking The Drive BeltRemoving the Drive Belt Installing the Drive Belt Using New Drive Belt Expanding Lower Drive Pulley Spare Drive Belt Replacement Left Side Gearbox How It Works Figure Springs High Engine RPM Driven Pulley Clutch Spring Driven Pulley CAM Bracket Moveable Fixed Face MAINTENANCE new style clutch Belt measurement Installing Drive Belt Lower drive pulley How it works Single Pitch MAINTENANCE TrowelBlade Pitch Adjustment Procedure Twin PitchTM Changing Blades Steering AdjustmentClean-Up „„Do the pitch control towers rock back and forth? Place the trowel in a FLAT, Level area Trowel Arm AdjustmentAssembly Distance from the lower wear plate Trowel Blade Removal Trowel Arm RemovalRemove the trowel arm from the spider plate Locate the trowel arm adjustment tool P/N Checking Trowel Arm Straightness Re-Assembly Installing Pans Onto Finisher BladesLifting/Crush Hazard.DO not lift trowel with pans attached Verify the hydraulic fluid level is correct Checking Steering PressureHydraulic Steering Pressure Move the throttle lever to Full engine RPM Steering Pressure Adjustment Steering Pressure Check Decommissioning trowel Decommissioning Trowel/Components Wiring Diagram Engine Starter Connector Orientation Front View Relay Orientation Troubleshooting Symptom Possible problem Solution Troubleshooting Ride-On Trowel Troubleshooting engine Air cleaner dirty? Clean or replace air cleaner HERE’S HOW to GET Help