Manuals / Brands / Computer Equipment / Network Card / National Instruments / Computer Equipment / Network Card

National Instruments NI WLS/ENET-9163 Setting Up the NI WLS/ENET-9000 Series Device

1 36

Download 36 pages, 1.26 Mb

NI WLS/ENET-9163 Carrier User Guide and Specifications 12 ni.com

Setting Up the NI WLS/ENET-9000 Series Device

Complete the following steps to prepare the NI WLS/ENET-9000 Series

device for use:

1. Before connecting the hardware, install NI-DAQmx software,

LabVIEW SignalExpress, and the NI-DAQ Device Documentation

Browser. Refer to the DAQ Getting Started Guide for more

information about software installation.

Note The NI-DAQmx software is included on the CD shipped with your kit and is

available for download at ni.com/support. After you install it, the NI-DAQ Device

Documentation Browser is available from Start»Programs»National Instruments»

NI-DAQ»Browse Device Documentation. The DAQ Getting Started Guide is available

after installation from Start»Programs»National Instruments»NI-DAQ»DAQ Getting

Started Guide.

2. If you are not using any mounting accessories or stacking the devices,

attach the provided rubber standoffs to the bottom of the

NIW LS/ENET-9000 Series device, as described in the Using the

NIWLS /ENET-9000 Series Device on a Desktop section.

3. Make sure the NI WLS/ENET-9000 Series device power is

disconnected.

4. Attach a ring lug, as shown in Figure6, to a 14 AWG (1.6 mm) wire.

Connect the ring lug to the ground terminal on the bottom of the device

using the ground screw. Attach the other end of the wire to the system

ground.

Contents

Main USER GUIDE AND SPECIFICATIONS NI WLS/ENET-9163 NI WLS/ENET-9000 Series Device 802.11g C Series Carrier NATIONAL 802.11g C Series Carrier Dimensions Safety Guidelines Safety Guidelines for Hazardous Voltages Related Documentation Page Page Page Device Documentation and Specifications Training Courses Technical Support on the Web Installing the Software Installing Other Software Example Programs Using the NI WLS/ENET-9000 Series Device Using the NI WLS/ENET-9000 Series Device on a Desktop Mounting the NI WLS/ENET-9000 Series Device Attaching the NI 9910 DIN-Rail Mounting the NI WLS/ENET-9000 Series to a Panel Configuring the Ethernet Connection Setting Up the NI WLS/ENET-9000 Series Device Connecting Power to the NI WLS/ENET-9000 Series Device 10/100BaseT(X) Ethernet Port Connection Device Interface Reset Button LED Indicators Pinouts Trigger Connector Cabling Using the NI WLS/ENET-9000 Series Device C Series I/0 Modules AI Sample Timing Analog Input Analog Input Triggering AI Start Trigger Signal Routing AI Start Trigger to an Output Terminal AI Reference Trigger Signal AI Pause Trigger Signal Analog Input Timing Signal AI Sample Clock Routing AI Sample Clock to an Output Terminal Convert Behavior For Analog Input Modules Scanned Simultaneous Sample-and-Hold Sigma-Delta Getting Started with AI Applications in Software Specifications Analog Input Digital Triggers Static Characteristics PFI Functionality Wireless (NI WLS-9163 Carrier Only) Receiver Sensitivity Antenna (NI WLS-9163 Carrier Only) Ethernet Module I/O States Power Requirements Physical Characteristics Antenna Safety Standards Safety Voltages RF Safety Warning (NI WLS-9163 Carrier Only) Environmental Shock and Vibration Electromagnetic Compatibility Electronic Compatibility Information CE Compliance EU Regulatory Statements Note Refer to the Declaration of Conformity (DoC) for this product for any additional regulatory compliance information. To obtain the DoC for this product, visit certification, search by model number or product line, and click the appropriate link in the Certification column. Environmental Management Waste Electrical and Electronic Equipment (WEEE) RoHS Regulatory Information United States Canada EuropeEU Declaration of Conformity Europe Restrictions for Use of 2.4 GHz Frequencies in European Community Countries Where to Go for Support