VCR Mode Tape Playback

Preparation

Before using the remote control, press the VCR but- ton to select the device to be operated.

Turn the TV on and select the video input source con- nected to the Recorder.

Audio system: Turn the audio system on and select the input source connected to the Recorder.

Normal Playback VHS

1

Insert a prerecorded video cassette.

The

indicator will light and the Recorder will power-

up automatically.

Make sure that the TIMER indicator in the display window is not lighted. If it is, press POWER once.

If a tape without a safety tab is inserted, the Recorder will start playback automatically.

2PLAY icon appears on the TV screen.Press PLAY (N) once.

It is not necessary to select the tape speed for play- back. It will be automatically selected by the Recorder.

3STOP icon appears on the TV screen.

If the tape reaches the end before STOP (x) is pressed,

the Recorder will automatically stop, rewind and eject the tape, and turn itself off.Press STOP (x) to stop playback.

otes

If you wish to watch the DVD playback during the VCR play- back, press DVD (or DVD/VCR) to change to DVD mode and perform the DVD playback. If you press VCR (or DVD/VCR) to watch the VCR playback again, playback resumes from the point where playback was interrupted.

You cannot playback from both DVD and VCR at the same time.

Tracking Control VHS

Auto Tracking

The automatic tracking function adjusts the picture to remove snow or streaks.

The AUTO TRACKING function works in the following cases:

A tape is played back for the first time.

Tape speed (SP, LP) changes.

Streaks or snow appear because of scratches on the tape.

Manual Tracking

If noise appears on the screen during playback, press either PR/CH(TRK) (v/V) on the remote control or PROG. (v/V) on the front panel until the noise on the screen is reduced.

In case of vertical jitter, adjust these controls very carefully. Tracking is automatically reset to normal when the tape is ejected or the power cord is unplugged for more than 3 sec- onds.

Special Effect Playback VHS

Special effects playback notes

Horizontal lines (noise bars) will appear on the TV screen. This is normal.

The audio is automatically muted during special effect modes, so there is no sound during search.

During the high-speed picture search modes, a short time is needed to stabilize tape speed when re-entering the PLAY mode. Slight interference may be observed during this time.

Search

This function lets you visually search forward and back- ward for a desired scene on your tape.

1Press BACKWARD (m) or FORWARD (M) during playback.

The Recorder will be activated in the SEARCH mode.

If the Recorder is left in the SEARCH mode for more than 3 minutes, the Recorder will automatically enter the PLAY mode, to protect the tape and video heads.

2To return to playback, press PLAY (N).

Still Picture and Frame-by-Frame Playback

1Press PAUSE/STEP (X) during playback. A still picture appears on the TV screen.

If a still picture vibrates vertically, stabilize it by using PR/CH(TRK) (v/V) on the remote control.

If the Recorder is left in the STILL mode for more than 5 minutes, the Recorder will automatically enter the STOP mode to protect the tape and video heads.

2Press PAUSE/STEP (X) repeatedly to advance the video picture one frame at a time while viewing a still picture.

3To return to playback, press PLAY (N).

Slow Motion

1While in still mode, press FORWARD (M).

The tape will be played back at a speed 1/19 times

slower than the normal speed.

During slow playback, use PR/CH(TRK) (v/V) on the Remote Control to minimize noise bands.

If slow motion mode continues for more than 3 minutes, the Recorder will automatically change to normal play

mode.

2To return to playback, press PLAY (N).

Counter Memory Function

This is useful if there is a section of tape you want to view immediately after recording or if you want to return to the same point several times.

1Begin recording or playing a tape.

2Press DISPLAY repeatedly to display the real-time counter on the TV screen.

3At the point you want to locate later, reset the real- time counter to 0:00:00 by pressing CLEAR. Continue to play or record.

4Press STOP when recording or playback finishes.

5Press RETURN (O).

The tape automatically stops when the tape counter returns to about “0:00:00”.

38

Page 38
Image 38
NEC NDRV-62 owner manual VCR Mode Tape Playback Preparation, Normal Playback VHS, Special Effect Playback VHS