NEC NEAX2000 IVS2

CHAPTER 4 CIRCUIT CARD INFORMATION

List of Required Circuit Card

NEAX2000 IVS2 Q-SIG System Manual

ND-70923 (E), Issue 1.0 Page 57

Lamp Indications

LAMP

NAME COLOR FUNCTION

RUN Green Flas hes at 120 IPM while this card is operating normally.

CRC Red Remains lit when detecting Cyclic Redundancy Checking (CRC)

errors.

PCM Red Remains lit when detecting PCM signal loss.

FRM Red Remains lit when detecting Frame Alignment signal loss.

RMT Red Remains lit when receiving Frame Alignment signal loss alarm

from a distant office.

AIS Red Remains lit when a pattern of consecutive “1” is received. The

distant office transmits this signal for a loop-back test.

BL Red B Channel status

ON : More than 10 channels are busy

OFF : All channels are idle

Flash (60 IPM) : Only one channel is busy

Flash (120 IPM) : 2 through 10 channels are busy

Contents

Main Page NEAX2000 IVS Q-SIG System Manual ND-70923 (E) NEAX2000 IVS Q-SIG System Manual TABLE OF CONTENTS LIST OF FIGURES LIST OF TABLES INTRODUCTION PURPOSE OUTLINE OF THIS MANUAL REFERENCE MANUALS Page Page 4 System Outline SYSTEM OUTLINE Summary Figure 1-1 System Outline of Q-SIG NOTE: Conforming to Q921-a (PBX-PBX Interface) Physical Interface 30DTI Figure 1-2 Physical Interface Figure 1-3 Physical Interface Physical Interface 24DTI Page 6 Interworking with Other Network Figure 1-4 Interworking with Other Network NOTE: Interworking between Q-SIG and CCIS is not available. System Configuration SYSTEM CONFIGURATION Figure 1-5 shows the system configuration of the Q-SIG system. CLOCK Figure 1-5 System Configuration of Q-SIG 30DTI DCH 24DTI DCH PLO Figure 1-6 Clock Supply Route Configuration CARD NAME AND FUNCTION Table 1-1 Q-SIG Card Name and Function CARD NAME FUNCTIONAL NAME FUNCTION SYSTEM CAPACITY Table 1-2 System Capacity for Q-SIG DESCRIPTION 24DTI 30DTI Page 12 System conditions SYSTEM CONDITIONS Time Slot Assignment Condition Figure 1-7 Accommodation of DTI/DCH/ICH/BRT/PRT into TDSW Time Slot Allocation for DTI/DCH Card Figure 1-8 Time Slot Allocation for DTI SERVICE FEATURES Connected Destination Indication Figure 1-9 Connected Destination Indication Page Transit Counter Relaying Figure 1-10 Transit Counter Page PRECAUTIONS STATIC ELECTRICITY GUARD Figure 2-1 Static Electricity Guard (1 of 2) Figure 2-1 Static Electricity Guard (2 of 2) WHEN MAKING A SWITCH SETTING ON A CIRCUIT CARD ATTENTION Caution REQUIRED EQUIPMENT Table 2-1 Required Equipment for Q-SIG EQUIPMENT DESCRIPTION QUANTITY REMARKS INSTALLATION PROCEDURE Figure 2-2 Installation Procedure for Q-SIG Mounting DTI and DCH Card Mounting CONN Card Page DTI Cable Connection via MDF Figure 2-3 Cable Connection via MDF Figure 2-4 Location of the AP Slots and the LTC Connectors for DTI Page 28 Figure 2-5 Example of MDF Cross Connection for DTI DTI Cable Connection via CONN Card Figure 2-6 Cable Connection via the CONN Card Page 30 Figure 2-7 Example of Coaxial Cable Connection Page HOW TO READ THIS CHAPTER DTI ASSIGNMENT Page Page Page DCH ASSIGNMENT TANDEM CONNECTION ASSIGNMENT To provide Tandem Connection (Tie Line to Q-SIG, Q-SIG to Tie Line), do the following programming. CONNECTED DESTINATION INDICATION ASSIGNMENT Page HOW TO READ THIS CHAPTER MOUNTING LOCATION OF CIRCUIT CARD Figure 4-1 Mounting Location of Circuit Card LIST OF REQUIRED CIRCUIT CARD Table 4-1 List of Required Circuit Card PN-CP14 (MP) Caution Page Page Page Page 50 PN-30DTC-A (DTI) Page Page Page Page Page Page 56 PN-24DTA-C (DTI) Locations of Lamps, Switches, and Connectors Page Page Page Page Page PN-SC01 (DCH) Page Page PZ-M542 (CONN) Lamp Indications This card has no lamps. Page PZ-M557 (CONN) Lamp Indications This card has no lamps.