Manuals / NEC / Computer Equipment / Computer Monitor

NEC RS-232C user manual Asset Data read and write, Asset Data Read Request and reply

Models: RS-232C

1 50

Download 50 pages 13.24 Kb

Page 18

8. Asset Data read and write

'0'-'0' (30h, 30h): Result code. No error.

'C'-'2’,'0'-'3'-'D'-'6' (43h, 32h, 30h, 33h, 44h, 36h): power control reply command

The monitor replies same as power control command to the controller. '0'-'0'-'0'-'1' (30h, 30h, 30h, 31h): Power mode

0001: ON

0002, 0003: Do not set.

0004: OFF (same as the power off by IR)

ETX (03h): End of Message

Check code

BCC: Block Check Code

Refer to the section 4.5 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

8. Asset Data read and write

MultiSync X461UN /X461HB /X431BT /P401 /P461 /P521 /P701 /S401 /S461 /S521 and MULTEOS M401 /M461

/M521 have the area for to store user’s asset data of up to 64bytes.

8.1 Asset Data Read Request and reply

This command is used in order to read Asset Data.

1) The controller requests the monitor to reply with Asset data.

Header	Message	Check code	Delimiter
SOH-'0'-Monitor ID-'0'-'A'-'0'-'A'	STX-'C'-'0'-'0'-'B'-'0'-'0'-'2'-'0'-ETX	BCC	CR

Header

SOH (01h): Start Of Header

'0' (30h): Reserved

Monitor ID: Specify the Monitor ID from which you want to get data. Ex.) If Monitor ID is '1', specify 'A'.

'0' (30h): Message sender is the controller.

'A' (41h): Message type is "Command".

'0'-'A' (30h, 41h): Message length is 10 bytes.

Message

STX (02h): Start of Message

'C'-'0'-'0'-'B' (43h, 30h, 30h, 42h): Asset read request command.

'0'-'0' (30h, 30h): Offset data from top of the Asset data. At first set 00h: Read data from the top of Asset data area.

'2'-'0' (32h, 30h): Read out data length is 32bytes.

Secondly set 20h: Read data from the 32bytes offset point in the Asset data area.

Maximum readout length is 32bytes at a time. ETX (03h): End of Message

Check code

BCC: Block Check Code

Refer to the section 4.5 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

2) The monitor replies Asset data to the controller.

Header	Message	Check code	Delimiter
SOH-'0'-'0'-Monitor ID-'B'-N-N	STX-'C'-'1'-'0'-'B'-	BCC	CR

Data(0)-Data(1)---Data(N)-ETX

Header

SOH (01h): Start of Header

'0' (30h): Reserved

'0' (30h): Message receiver is the controller.

Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to 'A', the replying Monitor ID is '1'.

(18/50)

Image 18

NEC RS-232C user manual Asset Data read and write, Asset Data Read Request and reply

Contents

3.1 RS-232C Remote control 2. Connectors and wiring2.1 RS-232C Remote control 1. Application4. Communication Format 4.1 Header block format fixed length3rdbyte Destination Destination equipment ID. Receiver Check code Delimiter 4.2 Message block formatHeader MessageCheck code 4.5 Check codeHeader Message DelimiterMessage 4.6 DelimiterHeader Check code5. Message type 5.1 Get current Parameter from a monitor5.2 Get parameter reply 5.3 Set parameter 5.4 Set parameter reply 5.5 Commands 5.5.1 Save Current Settings5.5.2 Get Timing Report and Timing reply 6. Typical procedure example 6.1. How to change the “Brightness” setting5.5.3 NULL Message SOH-0-0-Monitor ID-D-1-2 Page Step 1. Select a temperature sensor which you want to read Delimiter CR 0Dh End of packet 7. Power control procedure 7.1 Power status read7.2 Power control 1 The controller requests the monitor to control monitor power8. Asset Data read and write 8.1 Asset Data Read Request and reply8.2 Asset Data write 9. Date & Time read and write 9.1 Date & Time ReadThis command is used in order to write the setting of the Date & Time 9.2 Date & Time Write1 The controller requests the monitor to write Date & Time Message STX 02h Start of Message This command is used in order to read the setting of the Schedule 10. Schedule read and write10.1 Schedule Read 0-830h, 38h Message length Message STX 02h Start of Message 0-130h,31h VGA 0-230h,32h RGB/HV 0-330h,33h DVI 0-530h,35h Video1 Page 10.2 Schedule Write This command is used in order to write the setting of the Schedule 1 The controller requests the monitor to write ScheduleEX 0-130h, 31h Monday 0-430h, 34h Wednesday 2 The monitor replies a data for confirmation Page SOH-0-0-Monitor ID-B-0-C STX-C-3-1-5-ST-PG-EN-ETX1 The controller requests the monitor to write Schedule bit 4 Friday bit 5 Saturday bit 6 Sunday EX 0-130h, 31h Monday 1-731h, 37h 23 =17h 1-831h, 38h Off timer isnt set This command is used in order to read the Self-diagnosis status 11. Self diagnosis11.1 Self-diagnosis status read SOH 01h Start of Header 0 30h Reserved 12. Serial No. & Model Name Read This command is used in order to read a serial numberThis command is used in order to read the Model Name 12.1 Serial No. Read13. Security Lock 13.1 Security Lock ControlP1 Security Pass code 1st 0-030h, 30h SOH-0-MonitorID-0-A-1-0STX-C-2-1-D-EN-P1-P2-P3-P4-ETX P2 Security Pass code 2nd 0-030h, 30h0-130h, 31h Error C-3-1-D 43h, 33h, 31h, 44h Security Lock Control reply commandST-EN Lock condition result data ST Status 0-030h, 30h No error ETX 03h End of Message Check code BCC Block Check CodeAppendix A. Operation Code OP code TableADJUST AUDIO SCHDULEPage Information OSD OSD timer secondsMenu tree reset OSD TransparencyOption Advanced7 Autooffset Terminate Temperature sensor Carbon footprintAll data are subject to change without notice Revised at Mar.25/201050/50