General configuration, Pabx Mode SP5018A only | NEC SP5008A specification

2.3 General configuration

To make VoIP calls, you will need a SIP account provided by the SIP Proxy you are registered with. To configure the relevant SIP settings, please refer to the instructions explained below.

2.3.1 PABX Mode (SP5018A only)

This quick setting is used for MICRONET SP5018A to operate in PABX connection mode between PSTN and traditional PABX. Enable PABX mode for ISP/ITSP scenario that forbids SIP call to/from PSTN via the gateway (SP5018A). The call scenario will be working as below:

1.For FXO incoming call, it will route to corresponding FXS directly (1 by 1)

2.For FXS outgoing call, it will route to VOIP except those prefix set in FXO dialing Prefix.

3.For VOIP incoming call, it will route to FXS based on the called number

4.When VOIP call is failed to be called out such as register fail or network issue, the call will be route to FXO as backup.

5.When MICRONET SP5008A / SP5018A / SP5058A is malfunction or power failure, the all call will be directly bypassed to FXO.

PABX Connection	To enable PABX behavior or not.

SIP Setting	Please refer to 3.3.2.1

Representative Number Only	It is used (Yes) when you only have 1 SIP account and
	would like to be shared for all FXS lines. Please refer to

16

Image 17

NEC SP5008A General configuration, Pabx Mode SP5018A only, Pabx Connection, SIP Setting, Representative Number Only

Contents

IP Telephony Gateway Online Upgrade Web Administration Table of ContentIntroduction Startup Operation Specification Introduction Key Features Physical Description LED IndicatorsSP5058A SP5018A T1-T8 SP5008AL1-L8 T1/P1-T4/P4 Startup Login into the SystemPage Network Configuration Dhcp WAN Setting Static IP Enable/Disable this option Dhcp PPPoE Description LAN Setting Description Pabx Mode SP5018A only General configurationSIP Setting Pabx Connection FXO Dialing Prefix Primary FXS SIP settings SIP Setting Account PasswordNumber Display name SIP Advanced Setting Supports the feature, if the proxy does not support Make sure your proxy server or soft switchIt and you enable this feature, all IP outgoing calls Feature is for FXS only Payload Type Setting Page Line Setting No Answer Forward Time FXS only Enable HotlineLine1~Line8 relevant data Type RegPage Differentiated Services Code Point Setting Dscp Qos SettingDscp Signal ToS Setting ToS RTP Speed Dial Editor Speed Dial SettingSpeed Dial Speed Dial Editor In P2P application Peer to Peer call Caller ID Setting Line 1~Line Caller ID SettingDtmf Caller ID Start Symbol Dtmf Caller ID End Symbol Default symbol is C CDR mode CDR Server address CDR Server port CDR SettingPage Syslog mode Syslog Server address Syslog Server port Syslog SettingPage System setting Advanced ConfigurationPage Page Ping ip to keep alive network Ping timersec Sntp Setting Codec Priority Codec SettingCodec Packet Size Bandwidth Required Voice Setting You can set this option for each of the 8 lines Tone Setting Disconnect tone Phone Setting Country Min. Digit Count Digit Manipulation FXO Dial Prefix Third Example Dial PlanDial Plan Editor Page Provision Server Management Export File Import File Save-Reload setting Upgrade Firmware Updating the firmware by FTP Updating the firmware by Tftp Updating the firmware by Http Reset to Default Displays the MAC address of the WAN port Network Status Version Info Boot versionPost version Application version Register Proxy Port StatusPort Type Current password PasswordNew password Confirm new password Rebooting the system Enable the representative line Peer to Peer mode FXO to FXSConfiguration All the line and Disable all the register Enable the representative line Line 1~Line 8 Side B Peer to Peer mode FXS to FXS Page Page Page Specification SP5018A SP5058A Networking