Specification | NEC SP5008A specs

5. Specification

Model	SP5008A
Standard	SIPv2 (RFC 3261): Primary and Secondary Proxy, Primary and Secondary
	Outbound Proxy
POTS Interface	8 FXS
Ethernet Port	z	1 x RJ-45 WAN port of 10/100M
	z	4 x RJ-45 LAN ports of 10/100M
Voice	z	Codec: G.711a/mu-law, G.723.1 (6.3K), G.729, G.729.A
	z	VAD, CNG, and Silence Suppression
	z	Echo Cancellation (G.165 / G.168)
	z	Adaptive Jitter Buffer
	z	Packet Loss Compensation
	z	Adjustable volume level
DTMF	In-band, SIP Info, RFC2833
Telephony	z	Caller ID Detection: FSK, DTMF, ETSI (before ringing, between ringing)
	z	Call hold, Call transfer, Call waiting, Call forward (Unconditional, No
		answer, Busy, No Answer+Busy)
	z	Music on Hold
	z	Hotline and Waiting Time to Hotline
	z	Speed Dial and Peer-to-Peer Call
	z	Anonymous Call
	z	DND (Do Not Disturb)
	z	Dial Plan and Digit Manipulation
	z	Tone Generation/Detection: Ringing Tone, Ring Back Tone, Dial Tone,
		Programmable Tone
	z	CDR (Call Detail Record)
	z	MWI (Message Waiting Indication)
	z	FAX over IP: G.711 pass-through, T.38 Fax relay
PBX Features	z	Representative number setting
	z	Support SIP Trunk
	z	Extension calling among FXS ports
	z	Direct line (DID) to extension
	z	Max. 9 registrars (SIP trunk and 8 direct lines)
	z	Operator (Serial ring on extension) for attendant
Security	z	HTTP 1.1 basic/digest authentication for WEB access
	z	MD5 for SIP authentication (RFC 2069/2617)

72

Image 73

NEC SP5008A user manual Specification

Contents

IP Telephony Gateway Online Upgrade Web Administration Table of ContentIntroduction Startup Operation Specification Introduction Key Features Physical Description LED IndicatorsSP5058A SP5018A T1-T8 SP5008AL1-L8 T1/P1-T4/P4 Startup Login into the SystemPage Network Configuration Dhcp WAN Setting Static IP Enable/Disable this option Dhcp PPPoE Description LAN Setting Description Pabx Mode SP5018A only General configurationSIP Setting Pabx Connection FXO Dialing Prefix Primary FXS SIP settings SIP Setting Account PasswordNumber Display name SIP Advanced Setting Supports the feature, if the proxy does not support Make sure your proxy server or soft switchIt and you enable this feature, all IP outgoing calls Feature is for FXS only Payload Type Setting Page Line Setting No Answer Forward Time FXS only Enable HotlineLine1~Line8 relevant data Type RegPage Differentiated Services Code Point Setting Dscp Qos SettingDscp Signal ToS Setting ToS RTP Speed Dial Speed Dial SettingSpeed Dial Editor Speed Dial Editor In P2P application Peer to Peer call Caller ID Setting Line 1~Line Caller ID SettingDtmf Caller ID Start Symbol Dtmf Caller ID End Symbol Default symbol is C CDR mode CDR Server address CDR Server port CDR SettingPage Syslog mode Syslog Server address Syslog Server port Syslog SettingPage System setting Advanced ConfigurationPage Page Ping ip to keep alive network Ping timersec Sntp Setting Codec Priority Codec SettingCodec Packet Size Bandwidth Required Voice Setting You can set this option for each of the 8 lines Tone Setting Disconnect tone Phone Setting Country Min. Digit Count Digit Manipulation FXO Dial Prefix Dial Plan Editor Dial PlanThird Example Page Provision Server Management Export File Import File Save-Reload setting Upgrade Firmware Updating the firmware by FTP Updating the firmware by Tftp Updating the firmware by Http Reset to Default Displays the MAC address of the WAN port Network Status Version Info Boot versionPost version Application version Port Type Port StatusRegister Proxy Current password PasswordNew password Confirm new password Rebooting the system Configuration Peer to Peer mode FXO to FXSEnable the representative line All the line and Disable all the register Enable the representative line Line 1~Line 8 Side B Peer to Peer mode FXS to FXS Page Page Page Specification SP5018A SP5058A Networking