NEC uPD75P3116 7. INSTRUCTION SET

µ

PD75P3116

19

Data Sheet U11369EJ3V0DS

7. INSTRUCTION SET

(1) Representation and coding formats for operands

In the instruction’s operand area, use the following coding format to describe operands corresponding to the

instruction’s operand representations (for further details, refer to the RA75X Assembler Package Language User’s

Manual (U12385E)). When there are several codes, select and use just one. Codes that consist of uppercase letters and

+ or – symbols are keywords that should be entered as they are.

For immediate data, enter an appropriate numerical value or label.

Enter register flag symbols as label descriptors instead of mem, fmem, pmem, bit, etc. (for further details, refer to the

User’s Manual). The number of labels that can be entered for fmem and pmem are restricted.

Representation Coding Format

reg X, A, B, C, D, E, H, L

reg1 X, B, C, D, E, H, L

rp XA, BC, DE, HL

rp1 BC, DE, HL

rp2 BC, DE

rp’ XA, BC, DE, HL, XA’, BC’, DE’, HL’

rp’1 BC, DE, HL, XA’, BC’, DE’, HL’

rpa HL, HL+, HL–, DE, DL

rpa1 DE, DL

n4 4-bit immediate data or label

n8 8-bit immediate data or label

mem 8-bit immediate data or labelNote

bit 2-bit immediate data or label

fmem FB0H to FBFH, FF0H to FFFH immediate data or label

pmem FC0H to FFFH immediate data or label

addr 0000H to 3FFFH immediate data or label

addr1 0000H to 3FFFH immediate data or label (Mk II mode only)

caddr 12-bit immediate data or label

faddr 11-bit immediate data or label

taddr 20H to 7FH immediate data (however, bit 0 = 0) or label

PORTn Port 0 to Port 3, Port 5, Port 6, Port 8, Port 9

IE××× IEBT, IECSI, IET0 to IET2, IE0 to IE2, IE4, IEW

RBn RB0 to RB3

MBn MB0, MB1, MB15

Note When processing 8-bit data, only even-numbered addresses can be specified.

Contents

Main DATA SHEET PD75P3116 FEATURES FUNCTION OUTLINE PD75P3116 1. PIN CONFIGURATION (TOP VIEW) 64-pin plastic QFP (14 14): Note Always connect the VPP pin directly to VDD during normal operation. PD75P3116GC-AB8 64-pin plastic LQFP (12 12): PD75P3116GK-8A8 64-pin plastic LQFP (14 14): PD75P3116 PIN IDENTIFICATIONS PD75P3116 6 2. BLOCK DIAGRAM LCD controller/driver PD75P3116 3. PIN FUNCTIONS 3.1 Port Pins (1/2) 3.1 Port Pins (2/2) 3.2 Non-Port Pins (1/2) Page PD75P3116 3.3 Pin I/O Circuits The I/O circuits for the PD75P3116s pins are shown in abbreviated form below. (Continued) 3.4 Recommended Connection of Unused Pins Table 3-1. List of Unused Pin Connections Note When the subsystem clock is not used, select SOS.0 = 1 (on-chip feedback resistor not used). 14 4. Mk I AND Mk II MODE SELECTION FUNCTION Stack area specification Mode selection specification PD75P3116 PD75P3116 AND 5. DIFFERENCES BETWEEN 16 PD753104, 753106, 753108 6. MEMORY CONFIGURATION Figure 6-1. Program Memory Map Figure 6-2. Data Memory Map Note Memory bank 0 or 1 can be selected as the stack area. 7. INSTRUCTION SET Page Page Note Only the lower 3 bits in the B register are valid. Page Page Page Note - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 28 8. ONE-TIME PROM (PROGRAM MEMORY) WRITE AND VERIFY Page Page PD75P3116 32 9. ELECTRICAL SPECIFICATIONS Absolute Maximum Ratings (TA = 25C) Page Page DC Characteristics (TA = 40 to +85C, VDD = 1.8 to 5.5 V) 36 DC Characteristics (TA = 40 to +85C, VDD = 1.8 to 5.5 V) AC Characteristics (TA = 40 to +85C, VDD = 1.8 to 5.5 V) Page SBI mode (SCK...Internal clock output (master)): (TA = 40 to +85C, VDD = 1.8 to 5.5 V) AC Timing Test Points (Excluding X1, XT1 Input) Clock Timing TI0, TI1, TI2 Timing Serial Transfer Timing 3-wire serial I/O mode 2-wire serial I/O mode Serial Transfer Timing Bus release signal transfer Command signal transfer Interrupt input timing RESET input timing Data Memory Stop Mode Low Supply Voltage Data Retention Characteristics (TA = 40 to +85C) Data Retention Timing (STOP Mode Release by RESET) Data Retention Timing (Standby Release Signal: STOP Mode Release by Interrupt Signal) DC Programming Characteristics (TA = 25 5C, VDD = 6.0 0.25 V, VPP = 12.5 0.3 V, VSS = 0 V) Program Memory Write Timing Program Memory Read Timing Data output Data output t t V V VDD + 1 V 10. CHARACTERISTIC CURVES (REFERENCE VALUES) Supply current IDD (mA) Page 64-PIN PLASTIC QFP (14x14) 11. PACKAGE DRAWINGS 64-PIN PLASTIC LQFP (12x12) 64-PIN PLASTIC LQFP (14x14) 52 12. RECOMMENDED SOLDERING CONDITIONS Page 54 APPENDIX A. LIST OF PD75308B, 753108, AND 75P3116 FUNCTIONS Page 56 APPENDIX B. DEVELOPMENT TOOLS The following development tools have been provided for system development using the PROM Write Tools 58 Debugging Tools OS for IBM PCs The following operating systems for IBM PCs are supported. Page Page Page Notes on Target System Design Figure B-6. Connection Conditions of Target System (1) Figure B-7. Connection Conditions of Target System (2) Page Page Page 68 NOTES FOR CMOS DEVICES Regional Information Device availability Ordering information Product release schedule Availability of related technical literature