1234512345123451234512345 66666 1.PART NAMES AND FUNCTIONS. 123456

This compartment accommodates the remote control. The remote control serves as the key panel on the projector when it is plugged and fit in this compartment.

POWER ON/STANDBY Indicator

lights in green when the projector is turned on and lights in red when the projector is in standby.

1

￿@Ä¿

 

 

POWER

 

 

 

ON/STANDBY Indicator

 

OFF

BREAKER

ON

 

AC INPUT

 

 

 

OFF

POWER

ON

4 3 2

1 Breaker Switch

 

 

 

 

 

 

NOTE: Do not turn off the main power while “- -” on the

 

 

Press the switch to the ON position to turn on the breaker

 

 

 

 

and press to the OFF position to turn off the breaker.

 

 

two digit display is blinking. During this time the lamp is

 

 

When abnormal conditions are encountered, the breaker

 

 

cooling off.

 

 

will trip and turn the projector off.

 

 

 

 

 

 

6 POWER Indicator

 

If the projector will not be used for an extended period of

 

 

time, turn off the breaker by pressing the switch to the

 

Lights up when the projector is turned on.

 

OFF position.

 

7 STANDBY Indicator
2 Remote Sensor

 

 

Lights up when the projector’ s main POWER switch is on.

 

Receives the signal from the supplied remote control

 

 

 

When the projector is used with the ISS-6020 switcher on

 

when used in the wireless mode.

 

 

 

SW1 level or SW2 level mode, this indicator flashes when

 

 

 

3 Power Switch (Main power)

 

the projector is not connected with the switcher correctily

 

or when the switcher is turned off.

 

To turn on the main power to the projector press the

 

 

 

 

 

 

 

switch to the ON position (I). The STANDBY and the RC

 

8 RC READY Indicator

 

READY indicator will light.

 

Lights up when the projector’s main POWER switch is on.

 

In this condition you can start up the projector by pressing

 

 

 

Flashes when the projector receives a signal from the

 

the POWER ON button on the remote control or the

 

 

 

remote control.

 

POWER button on the side panel.

 

 

 

 

 

 

 

Press to the OFF position (0) to turn the main power off.

 

9 LAMP Indicator

 

 

 

 

NOTE: When turning off the main power, first return the

 

Displays the lamp on or off.

 

projector to the standby condition by pressing the

 

Indicator illuminates—Lamp is turned on

 

POWER OFF button on the remote control or the POWER

 

Indicator goes out-Lamp is turned off

 

button on the side panel and then turn off the main

 

 

 

 

 

POWER switch. These procedures are necessary to

 

0 Two Digit Display

 

protect your projector and the connected equipment.

 

INDICATOR: Displays projector error codes.(“00” in

4 AC INPUT

 

normal operation)

 

ON/OFF Switch: Turns the INDICATOR on or off.

 

Connect the supplied power cord here (AC 200-240V).

 

A REMOTE 2 Jacks
5 POWER Button

 

 

IN: for the wired remote control.

 

Turns the projector on when the projector is in the

 

OUT: for daisy-chaining multiple projectors and operating

 

standby condition (Main Power switch must be on and

 

them with the same remote control. To do so, connect to a

 

the STANDBY indicator lit). Turns the projector off after

 

second projector’ s IN terminal to relay the input at the IN

 

“- -” on the two digit display is blinking for three min-

 

terminal of the first projector until all the projectors are

 

utes.

8

connected.