NEC XL-3500 5.APPENDIX, Code, Message, Message List

1234512345123451234512345 66666 5.APPENDIX 123456

Message List

Code	Message
A1	PS PROTECT ERROR (Overload or failure in the mains power supply)
A2	POWERGOOD ERROR (Insufficient voltage of +5V(D) or DLP5V in the mains power supply)
C0~CF	COMUNICATION ERROR (Communication setting errors in conjunction with switcher and PC control)
D0	SIGNAL UNLOOK (Instability or failure in synchronization)
E0	FAN STOP ERROR (Fan stoppage)
EC	FLASH MEMORY ERASE ERROR (Error in system PWB)
ED	FLASH MEMORY WRITE ERROR (Error in system PWB)
EE	ALL STORE DATA INITIAIZING (Store ROM formatting)
EF	PARTLY STORE DATA IS BREAKING (Error in stored data)
F0	H-FREQUENCY LIMIT OVER (Entry of signal input at 120kHz or above)
F1	ENGINE TEMPERATURE EROOR (Engine temperature deviating the specified range)
F2	12CBUS EROOR (VIDEO PRO PWB or CORE PACK) (Control error in video PRO PWB/core PACK)
F3	12CBUS ERROR (DLP ENGINE) (Engine control error)
F4	LAMP PROTECT EROOR (Lamp source error/lamp error or lamp’s fan stop)
F5	LAMP STATE ERROR (Lamp error)
F6	LAMP TEMPERATURE ERROR (Lamp’s temperature error)
F7	MUSEBUS ERROR (Error in graphic PWB)
P0	FPGA (OSD) WRITING (Writing in FPGA)
P1	FPGA (R) WRITING (Writing in FPGA)
P2	FPGA (G) WRITING (Writing in FPGA)
P3	FPGA (B) WRITING (Writing in FPGA)
PP	BIOS PROGRAM STATING (Program writing being processed)
o0~oF	Internal processing

80

Contents

MultiSync Hivid 3500 Projector CAUTION: 3. GSGV Acoustic Noise Information Ordinance: WARNING Precautions AVERTISSEMENT Installation Power Supply Cleaning Fire and Shock Precautions Alimentation Nettoyage Précautions contre l'incendie ou la décharge LIMITED WARRANTY TABLE OF CONTENTS INTRODUCTION 1.PART NAMES AND FUNCTIONS 2.INSTALLATION 3. OPERATION Congratulations On Your Purchase Of The MultiSync Hivid 3500 Projector The features you’ll enjoy include: How Do You Get Started What’s In The Box 1.PART NAMES AND FUNCTIONS 1.PART NAMES AND FUNCTIONS H I J K L M N BOPTION Connectors (D-Sub 9-pin) CREMOTE 1 Connector (Mini D-Sub 15-pin) DINPUT E OPTIONAL Boards Rotary switch (S1001) Jumper (S1002, S1003, S1004) Setting of Rotary switch No Mark Remote control unit BHELP Button CSIG LEVEL Button DGAMMA Button EADDRESS Button FPIXEL CLK Button Remote Control Battery Installation 1. Press firmly and slide the battery cover off 2. Remove both old batteries and install new ones (AA) Ensure that you have the batteries’ polarity (+/-)aligned correctly 3. Slip the cover back over the batteries until it snaps into place When using the remote control as the key panel on the projector: Setting Up Your MultiSync Hivid 3500 Projector Moving The Projector Selecting A Location Pulling Out the Handles Retracting the Handles ■Projection Distance Ceiling Installation Reflecting The Image Rear Screen Projection EXAMPLES OF CONNECTIONS CAUTIONS ON CONNECTIONS: When Used with One Switcher (ISS-6020/ISS-6020G) How to make connections: Set the DIP switch (S8601) of the Switcher as follows: When used with the Switcher When used in stand alone operation 3.OPERATION General Controls Using The On-ScreenMenus When a passcode has not been registered: When your passcode has already been registered: Menu Descriptions & Functions Storing Projector Settings (Automatic Save Feature) Basic Operation (Operate Menu) When using the projector in stand alone operation: When using the projector with the ISS-6020/ISS-6020G: When using the projector with two ISS-6020/ISS-6020Gor more: Source Information ■Source Name ■Direct Key ■Input Slot ■Sync System ■Sync Termination ■Display Mode ■Color Matrix ■CTI(Color Transient Improvement) Control ■Noise Reduction ■Stadium Mode ■Source Select Counter ■Source Display Timer Picture Control Hue ■Pixel Clock / Pixel Phase ■Zoom/Pan ■Image Position ■Blanking Sound Control (only when used with the ISS-6020/ISS-6020GSwitcher) Closed Caption Timer Setting Page Adjusting and Setting (Adjustment) ■Source Registry 1)To Select a Slot When using with a single Switcher ISS-6020/ISS-6020G: When using with two or more ISS-6020/ISS-6020Gswitchers: 2)To Select Signal System To Set HDTV or not When Selecting Component Signal 4)To Input a User Name 5)To Select a Registry Number ■Registry Edit Amplitude White Balance Signal Level Uniformity To Adjust White Uniformity To Adjust the Edge Blending Display Function 1) Field Handling 2)Interlace Mode 3)Sync Protect Lamp Mode ■Entering Passcode ■Registering Passcode Page ■Changing Your Passcode Page ■Canceling Your Passcode Page ■PJ Orientation ■Default Source Select When used in stand alone operation: The default input screen will be displayed When used with a single Switcher: When used with two or more Switchers: ■S-VideoMode Select ■Video System Select ■Auto Data Store ■Option Terminal Speed ■Uniformity Switching ■Message Time Page ■Date, Time Preset ■Display Item Set ■Connect Condition ■PJ Address mAddressing the Remote Control Unit Address common to all the projectors A D D R E S S R C U N I T ∗∗ ■Help ■Topics ■Set Information ■Test Patterns ■Normal, Load, and Cancel Function ■To return to the last stored level (Load): ■To cancel the adjustment data (Cancel): Page Page 5.APPENDIX Message List Code Message NEC Corporation