Manuals / Net Optics / Computer Equipment / Network Card

Net Optics 96547iTP, 96542iTP manual Connecting Power, iTap GigaBit Dual Port Aggregator

Models: 96547iTP 96542iTP

1 52

Page 21

iTap GigaBit Dual Port Aggregator

	A	Network		B	1	2	Dual Port Aggregator
®		Network					GigaBit Copper
®

2	A
1	B RESET
	ACT LINK		ACT LINK		ACT LINK	ACT LINK
www.netoptics.com						Monitor

To monitoring device 1

To monitoring device 2

Figure 13: 96547iTP Monitor Connections

Connecting Power

For power fault protection, the iTap has redundant power supplies. The second power supply is available to support the ﬂow of trafﬁc to the monitoring device in the event that the ﬁrst power supply becomes unavailable. If the ﬁrst power supply is unavailable, the second power supply provides all power for the iTap. Even if no power is available to the passive iTap, network trafﬁc ﬂows uninterrupted.

If you plan to use redundant power, make sure that you connect the power supplies to two separate, independent power sources. After connecting the power supplies, verify that at least one Power LED is illuminated.

Page 21

Image 21

Net Optics 96542iTP manual Connecting Power, iTap GigaBit Dual Port Aggregator, 96547iTP Monitor Connections

Contents

User Guide iTap GigaBit Dual Port Aggregator Models 96542iTP and 96547iTPDoc. PUB542iTPU Rev. 1, 3/06 PLEASE READ THESE LEGAL NOTICES CAREFULLY Trademarks and CopyrightsAdditional Information Chapter Installing the iTap ContentsChapter Using the Front Panel Interface Chapter IntroductionChapter Using System Manager Chapter Using Web ManagerAppendix B Command Line Interface Appendix A Speciﬁcations and ModelsOverview Chapter IntroductionIntelligent TapTM Performance AggregationTrafﬁc Monitoring Access Information AnywhereSeeing is Believing Web ManagerSecurity, Visibility, and Reliability System ManagerEase of Use SupportiTap GigaBit Dual Port Aggregator MemorySide A Router Side B Side A + Side B Monitoring DeviceThe NIC receives 800 Mbps 80% utilization, so no memory is required for the monitoring devices NIC to process all full-duplex trafﬁc iTap GigaBit Dual Port AggregatorUnpacking and Inspection About this GuideiTap GigaBit Dual Port Aggregator iTap Physical Features Chapter Installing the iTapOverview iTap GigaBit Dual Port AggregatorFigure 4 96547iTP Front Panel Features iTap Port Aggregator LEDsFigure 5 Rear panel features iTap GigaBit Dual Port AggregatorUsing the Command Line Interface CLI Planning the InstallationConﬁguring the iTap iTap GigaBit Dual Port AggregatoriTap GigaBit Dual Port Aggregator To access the iTap CLIset password password To change the username and passwordset username username To set the iTap IP addressTo disable the display and remote interfaces To display current settingsTo set the current date and time Figure 7 Show Set Command ExampleMounting the iTap To use the Help commandTo rack mount the iTap iTap GigaBit Dual Port AggregatorConnecting to the Network Connecting the Management PortTo connect the iTap Management Port To connect the iTap to your networkTo Switch, Server, or Router DTE Rx B To Switch, Server, or Router DCETx A To DCE network switch or routerConnecting to the Monitoring Devices To connect the iTap to your monitoring deviceiTap GigaBit Dual Port Aggregator Connecting Power iTap GigaBit Dual Port AggregatorFigure 13 96547iTP Monitor Connections iTap GigaBit Dual Port Aggregator Checking the InstallationDisplay Chapter 3 Using the Front Panel InterfaceOverview iTap GigaBit Dual Port AggregatorPower LEDs Utilization Alarm LEDsReset Button Link LEDsAccessing Web Manager Chapter Using Web ManagerTo access Web Manager iTap GigaBit Copper Port AggregatorFigure 15 Web Manager Page iTap GigaBit Copper Port AggregatoriTap GigaBit Copper Port Aggregator Viewing System StatusiTap GigaBit Copper Port Aggregator Viewing StatisticsConﬁguring the iTap iTap GigaBit Copper Port AggregatorWeb Manager has both read-only and read/write ﬁelds. Use the read/write ﬁelds in the iTap Conﬁguration section of the Web Manager page to set conﬁguration parameters see Figure Disable DisableDisable DisableInstalling System Manager Chapter Using System ManagerTo install System Manger OverviewFigure 21 Select Installation Folder iTap GigaBit Dual Port AggregatorFigure 20 Welcome Dialog Box iTap GigaBit Dual Port Aggregator Figure 22 Conﬁrm Installation Figure 23 Installation ProgressiTap GigaBit Dual Port Aggregator Figure 24 Installation CompleteTo access System Manager Exploring System ManageriTap GigaBit Dual Port Aggregator Creating a Group Using the ToolbarTo create an iTap group iTap GigaBit Dual Port AggregatorAdding iTaps Deleting a GroupTo delete a Group To add an iTap to the system4. Select your model of the iTap from the Product drop-down list iTap GigaBit Dual Port Aggregator7. Repeat Steps 1-6 for each iTap you are adding iTap GigaBit Dual Port AggregatorDeleting an iTap To delete an iTap from System ManageriTap GigaBit Dual Port Aggregator Conﬁguring an iTap To conﬁgure the iTapiTap GigaBit Dual Port Aggregator Viewing iTap Information To view iTap informationiTap GigaBit Dual Port Aggregator Figure 35 View Type List iTap GigaBit Dual Port AggregatorModifying an iTap To modify the iTap conﬁgurationiTap GigaBit Dual Port Aggregator Power Supply Output Power Supply InputOperating Temperature Storage TemperatureiTap Command Line Interface Monitor Port Output PowerWiFi Optical Interface 96542iTPAvailable Models Wireless Option AccessoriesModels iTap GigaBit Dual Port AggregatorCommand Appendix B Command Line InterfaceiTap GigaBit Dual Port Aggregator SyntaxiTap GigaBit Dual Port Aggregator CommandSyntax DescriptioniTap GigaBit Dual Port Aggregator Page 2006 by Net Optics, Inc. All Rights Reserved