INSTALLATION
INSTALLING GAS LOG HEATER FIREBOX MODELS MA CVFB200LP OR
MA CVFB200NAT
CAUTION: Do not remove the metal data plates attached to the heater as- sembly. The data plates contain impor- tant warranty information.
CAUTION: After installation and periodically thereafter, check to ensure that no flame comes in contact with any log. If so, reposition logs according to the log installation instructions in this manual. Flames contacting logs will create soot.
1. Remove logs and heater from carton. |
6. Inside of Firebox you will find three | MANUAL |
(3)wires with a switch attached. Dis- connect the wires from the switch.
Using the remaining mounting bracket SWITCH
with the switch holder on top, feed |
|
the wires through the wire channel | RED |
starting at the end opposite the switch | |
holder. Continue through the switch | WIRE |
hole in top. Reconnect the three (3) | MOUNT- |
wires to the switch (make sure the red | |
wire is connected to the Manual side | ING |
of the switch, see page 33). Position | BRACKET |
the switch in the switch holder, press |
|
until switch locks into position. (See |
|
Figure 15). Take mounting bracket |
|
and attach to left rear side of stove, |
|
with bolts provided. (See Figure 14) |
|
7. Place freestanding stove in desired |
|
position in room. Be sure to maintain |
|
clearances to combustibles as outlined |
|
on page 6. |
|
8. After positioning stove in desired po- |
|
sition, connect gas supply and com- |
|
plete all pressure checks and light the |
|
heater. (See page 14 Connecting To |
|
Gas Supply) |
|
OFF AUTO
SWITCH
HOLDER
WIRE
CHANNEL
NOTE: Do not pick up gas heater by | |
the burner itself. This could damage | |
heater. Always handle the heater by | |
the firebox only. |
|
2. Remove all protective packaging ap- | |
plied to logs and gas log heater for | |
shipment. |
|
3. Check all items for any shipping | |
damage. If damaged, promptly inform | |
dealer where you bought heater. Place | |
the logs into the Firebox and follow | |
the directions on page 10, Figure 13. | |
4. If not already removed, remove back | |
panel from assembled stove body | |
(Stoves sold for the use of a Model | |
CVF200’s series may not have a back | |
panel, just the bolts). See back panel | |
and bolts on page 7, Figure 5. Use a | |
10mm socket or an adjustable | |
wrench. Remove six (6) bolts and | |
washers. Keep bolts and washers to | |
attach Rear Mounting Brackets. | |
5. From rear of stove slide the Firebox | |
into the Cast Stove until the front of | |
the Firebox touches | the inner front |
rear side of the stove. The Firebox | |
has two Alignment Guides made to | |
the bottom of the Firebox. These will | |
ensure a more proper center align- | |
ment of the Firebox in the Cast Stove. | |
Then take the mounting bracket with- | |
out a switch holder and align slots in | |
bracket with top and | bottom holes on |
right side of stove. Fasten with bolts | |
provided. (See Figure 14) | |
FIGURE 15 - BRACKET/WIRE
CHANNEL
SWITCH HOLDER (ALSO REFER TO
PAGE 16)
LEFT | SWITCH | OPTIONAL AIR CHANNEL/ | RIGHT | |
BLOWER ASSEMBLY | REAR | |||
| ||||
REAR |
|
| SIDE | |
SIDE |
|
|
| |
|
| MOUNTING BRACKETS |
| |
BOLTS |
|
| BOLTS | |
|
|
|
Alignment Guides
FIGURE 14 - BACK OF STOVE WITH FIREBOX INSERT / MOUNT- ING BRACKETS / SWITCH/ OPTIONAL AIR CHANNEL WITH BLOWER.
11
