Continued | New Buck Corporation GAS STOVE HEATER instruction

CONTINUED

CONTINUED

9.After lighting the heater check to ensure that the log placement is cor- rect, and that no flame is coming in contact with the logs. If log place- ment is incorrect reverse steps 5 and 6, and see page 10, Figure 13.

REMOVING CAST STOVE FRONT PANEL

If at some time you may need to remove the front panel of your Cast Stove unit for servicing or replacement follow these steps.

A. Facing the front of the unit with ac- cess door in the closed position remove the two (2) hex screws holding bottom front of stove in place. Screws are lo- cated on the bottom front between the access door and front legs. You may dis- card the screws . (See Figure 16)

B. Remove the Center Grate located on the top of the unit.

C. Using an Allen wrench, remove the Alignment Stud (Allen Screw) from the top front center of the unit.

NOTE: Be prepared to hold the Front Panel while removing the Alignment Stud. The panel may come out by ap- plying pressure, and may cause damage to the panel or cause personal injury.

D. Replace front panel and (Allen screw) Alignment Stud before returning to nor- mal usage.

ALIGNMENT STUD

CENTER GRATE

(ALLEN SCREW)

FRONT PANEL

DOUBLE DOORS

FRONT PANEL SHIPPING SCREWS (DISCARD)

FIGURE 16 - FRONT OF CAST STOVE/FRONT PANEL

12

Image 16

New Buck Corporation GAS STOVE HEATER installation manual Removing Cast Stove Front Panel, Continued

Contents

Page Page TABLE OF CONTENTS IDENTIFICATION NUMBERS AND DESCRIPTIONS FOR CAST STOVE SERIES SAFETY INFORMATION WARNINGS VENT-FREENATURAL OR L.P GAS STOVE HEATER PRODUCT FEATURES SAFETY PILOTPRODUCT INDENTIFICATION LOCAL CODES AIR FOR COMBUSTION AND VENTILATION PROVIDING ADEQUATE VENTILATIONUnusually Tight Construction Confined and Unconfined Space Continued DETERMINING FRESH-AIRFLOW FOR HEATER LOCATION Ventilation Air From Outdoors VENTILATION AIRContinued INSTALLATION GAS CONNECTIONCLEARANCES TO COMBUSTIBLES Vent-FreeOperation Only STOVE CAVITY ASSEMBLY Continued 10.Install door catch bolt M8 Continued MA C100BATNAT ContinuedIMPORTANT Make “LOG #2 PLACEMENT” MA CVFB200NAT INSTALLATIONGas Supply REMOVING CAST STOVE FRONT PANEL CONTINUED INSTALLATION OF OPTIONAL BLOWER ASSEMBLY MODEL MA CVF714 CONNECTING TO GAS SUPPLY Installation Items NeededAccessories, page Continued Pressure Testing Heater Gas Connections Pressure Testing Gas Supply Piping SystemFor purpose of input adjustment ContinuedPage FLAME ADJUSTMENT KNOB THERMOCOUPLE PILOT BURNER SWITCHIGNITOR ELECTRODE IGNITOR BUTTON OPTIONAL REMOTE CONTROL See Troubleshooting, pages 20 throughContinued PILOT FLAME PATTERN MILLIVOLT INSPECTING AND CLEANING MAINTENANCE LOGSMAIN BURNER TRANSPORTING STOVE OBSERVED PROBLEM Cleaningand Maintenance, page 19 or Maintenance OBSERVED PROBLEM Cleaning and Maintenance, pagePOSSIBLE CAUSE REMEDY OBSERVED PROBLEM and Maintenance, pageWARNING If you smell gas Shut off gas supply Do not try to light any appliance ACCESSORIES SERVICE HINTSREPLACEMENT PARTS WALL THERMOSTAT PART# PE PARTS LIST FOR MODELS MA C100BALTLP, MA C100BATNAT, ANDMA CVFB200LP, MA CVFB200NAT NOTE REFER TO PAGES 25 ANDPage Page PARTS BREAKDOWN FOR CAST STOVE SERIES TOWNSEND Discarded During Assembly PARTS LIST TOWNSEND PARTS AVAILABLE-NOTSHOW TOWNSEND PARTS BREAKDOWN FOR CAST STOVE SERIES HEPPLEWHITE PARTS LIST HEPPLEWHITE PARTS AVAILABLE-NOTSHOWN HEPPLEWHITE PARTS LIST HEPPLEWHITE WIRING DIAGRAM