Nintendo 2000 specification

7.Click Finish to complete the installation.

8.After the installation is completed, verify that the USB LED is lit on the front of you cable modem. If not, refer to the troubleshooting section later in this chapter.

User’ Guide

22

Image 22

Nintendo 2000 manual

Contents

Orion Contents Nvram Tftp Mode of Operation Understand the Cable Modem’s Features Contact Your Local Cable Operator Supplied Prepare Your Area for Cable Modem InstallationGather Supplied and Required Items Not Supplied Installing the Cable Modem Using the USB Port Installing the Software Drivers Before Hardware ConnectionPage Page Installing the Hardware Installing the Software Drivers User’ Guide User’ Guide Page Page Page User’ Guide Page Click Yes to restart the computer User’ Guide Page Page Page Page Page Click Finish to complete the installation User’ Guide Troubleshooting the USB Installation None of the LEDs is on when I power on the LAN Cable Modem Uninstalling the USB Driver Select USB Composite Device and click Remove Click Refresh Installing the Modem Using the Ethernet Port None of the LEDs are on when I power on the Cable Modem Troubleshooting the Ethernet InstallationEnet LED on my cable modem is not lit Page Cable Modem LEDs and Connectors LEDs on the Front of the Modem Connectors on the Back of the Modem Telnet commands Getting Help CMshow interTab CMshow interface Redisplaying a command CMshow ? Debug Image Ping Tracert PasswordUser-Level Show ¾ show interface ethernet ¾ show interfaceCMshow interface ? CMshow interface ethernet ¾ show interface usb CMshow running-configCMshow interface usb Qpsk ¾ show cpe-info Display CPE information ¾ show cpe-limit CMshow downstream CMshow cpe-limit¾ show downstream Display downstream information ¾ show upstream ¾ show nat timer ¾ show nat configCMshow nat config ¾ show rip CMshow access-list CMshow nat timer¾ show access-list ¾ show pppoe-forwarding Display PPPoE enable or disable Host-name CM dhcp ip-pool 192.168.10.2 CMshow dhcp ¾ host-name delete Delete host-nameCustomer-123host-name delete ¾ dhcp ip-pool delete ¾ dhcp gateway ip address Set local Dhcp gateway ip address ¾ dhcp reserve-mac delete 1-16all One to one mapping ¾ dhcp dns delete 1~4/allCMnat static ipmapping add 64.168.39.3 Port forwarding setting ¾ nat static ipmapping delete index/all CMnat static portmapping delete CMnat static ip disableCMnat static ip enable NAT static ip Interfaces CMnat static gateway ¾ interface ethernet startup ¾ interface cable upstream channel id ¾ interface usb shutdown ¾ interface cable rip send-version¾ interface cable startup ¾ interface usb startup ¾ rip silence-mode enable/disable ¾ rip timer response 10-65535 second¾ rip version 1/2/2b CMrip key-chain 1 1 key-string abcdefg ¾ rip defaultCMrip key-chain 1 1 start-time 2002-04-20 Access-list ¾ web-access password string Set web-access password ¾ pppoe-forwarding enabledisable CMaccess-list 21 permit 192.168.100.10¾ access-list delete list IDall CMcopy tftpconfig 68.5.203.15 4ips.txt ¾ snmp community string ro ¾ reset¾ snmp community ¾ write NAT mode Bridge mode¾ ip nat enable Routing mode ¾ ip route enable NAT/Routing mode ¾ ip natroute enable Accessing the Web User Interface Web User Interface Home Cable Modem Information Cable Modem Status Downstream Upstream Upstream Burst Operation Parameters Event Log Router/NAT configuration Bridge Mode WAN Interface NAT Mode Gateway LAN InterfaceReset Submit Router Mode Routing Protocol LAN Interface Add Key ChainDelete NAT Router Mode Routing Protocol Gateway LAN Interface Authentication mode Authentication Key Chain Reset Gateway LAN Setup Page Docsis configuration file Vsif tag support