37. Thread the end of the High Cable (54) into the | 37 |
|
|
|
|
Cable Tool (27). Route the Cable Tool and Cable |
|
|
|
| |
|
|
|
| 74 | |
through the Side Top Frame (7). Make sure that |
|
|
|
| |
|
|
|
| 45 | |
the Cable Tool is routed through the bolts in |
|
| Between | ||
|
|
| |||
the Top Frame as indicated; if the High Cable |
|
| Bolts |
| |
rubs against a bolt, damage may occur. |
|
| 7 |
|
|
Remove the Cable Tool from the Cable. |
|
|
|
| |
|
|
|
|
| |
Hold a 3 1/2” Pulley (45) inside the High Cable | 54 |
|
|
|
|
|
|
|
|
| |
(54) as shown. Attach the Pulley inside the brack- |
|
|
|
| 62 |
et on the Center Top Frame (2) with an M10 x | 27 |
|
|
|
|
48mm Button Bolt (74) and an M10 Nylon |
|
|
|
| |
Locknut (62). |
|
|
|
|
|
38. Make sure the High Cable (54) is routed under | 38 |
|
|
|
|
the indicated rods on the Swivel Arm (14). |
|
|
|
| |
| 62 |
|
|
| |
|
|
|
|
| |
Attach a 4” Pulley (89) inside the Swivel Arm (14) |
| 65 14 |
|
| |
Rods |
|
|
|
| |
with an M10 x 54mm Button Bolt (73), two M10 |
|
|
|
| |
|
|
|
|
| |
Washers (65), two 7mm Spacers (48), and an |
|
| 65 |
|
|
M10 Nylon Locknut (62). Make sure the High |
|
|
|
| |
|
|
|
|
| |
Cable (54) rests in the groove of the Pulley. |
| 48 |
| 73 |
|
|
|
|
|
| |
|
| 54 | 89 |
|
|
|
|
|
|
| |
|
|
| 48 |
|
|
39. Slide a Clip Cover (43) onto the High Cable (54). | 39 |
|
|
|
|
|
|
|
|
| |
Hold an M6 Nylon Locknut (63) inside a Clip (42), |
|
|
|
|
|
and insert the High Cable (54) into the Clip and |
|
|
|
|
|
the Locknut. Insert a screwdriver between the |
|
| 54 |
|
|
Locknut and the Clip. Rotate the screwdriver, the |
| 43 |
|
|
|
Clip, and the Locknut together until two threads of |
|
|
|
| |
|
|
|
|
| |
the Cable show past the Locknut. |
|
|
|
|
|
Slide the Clip Cover (43) over the Clip (42). |
| 42 | 63 |
|
|
|
|
|
| ||
|
|
|
|
| |
40. Route the Cable Tool (27) through the Left | 40 |
|
|
|
|
Stabilizer (92). Make sure that the Cable Tool is |
|
|
|
| |
|
|
|
|
| |
routed around the bolts in the Stabilizer as |
|
|
|
|
|
indicated; if the Low Cable (55) rubs against a |
|
|
|
| 27 |
bolt, damage may occur. |
|
|
|
| |
|
|
|
|
| |
Locate the Low Cable (55). Thread the end of |
| 42 |
|
| 55 |
the Cable without the Clip (42) into the Cable Tool |
|
|
| ||
(27). Make sure the Cable is inside the indicat- |
| 89 |
|
| |
ed rod on the Swivel Arm (14). Pull the Cable |
|
|
| ||
|
| 48 |
|
| |
through the Left Stabilizer (92). Remove the |
|
|
| 92 | |
Cable from the Cable Tool. |
|
|
|
| |
| 48 |
|
|
| |
|
|
|
|
| |
Attach a 4” Pulley (89) inside the Swivel Arm (14) | 73 |
|
|
|
|
with an M10 x 54mm Button Bolt (73), two M10 |
|
|
|
| |
Washers (65), two 7mm Spacers (48), and an | 65 |
|
|
| |
|
|
|
|
| |
M10 Nylon Locknut (62). Make sure the Low | Rod | 14 | 65 | 62 |
|
Cable rests in the groove of the Pulley. |
|
|
|
| |
|
|
|
|
| |
| 15 |
|
|
|
|
