Preparing to Install the ARN | Nortel Networks Passport ARN Routers

Chapter 1

Installing the ARN

This chapter describes how to install the Passport ARN router, as follows:

Topic	Page

Preparing to install the ARN	1-1

Installing the ARN	1-5

Understanding the ARN module locations	1-9

Connecting communications cables	1-10

Connecting a management console	1-23

Connecting back-panel modem interfaces	1-27

Connecting the power cables	1-29

Installing the flash memory card	1-31

Where to go next	1-32

Note: The installation instructions in this chapter assume that wiring is already installed on the premises using common cable system practices. Your installation procedure may differ slightly, depending on your cable system.

Preparing to Install the ARN

Verify the following before beginning the installation, as explained in the sections that follow:

•Your shipment is complete and undamaged.

•You have the proper equipment and tools.

114200-E Rev 00

1-1

Image 25

Nortel Networks Passport ARN Routers manual Preparing to Install the ARN, Topic

Contents

Installing and Operating Passport ARN Routers Trademarks Copyright 2000 Nortel NetworksStatement of Conditions USA Requirements Only Taiwan Requirements Japan/Nippon Requirements OnlyCanada Requirements Only Canada CS-03 -- Règles et règlements FCC Part 68 Compliance Statement Nortel Networks NA Inc. Software License Agreement Vii Page Contents Chapter Starting the ARN Chapter Installing a WAN Adapter Module Appendix B Using Local Boot the Quick-Start Procedure Appendix D Requirements for European Operation Page Figures Figure B-1 Tables Table C-2 Before You Begin Preface Bold text Text ConventionsPing Example Enter show ip alerts routes Acronyms Carrier sense multiple access with collision detection Challenge handshake authentication protocolChannel service unit Data service unit Hard-Copy Technical Manuals Technical Solutions Center Telephone How to Get Help Topic Preparing to Install the ARN Verifying Shipment Contents Accessories in the ARN Shipping Container Cables Additional EquipmentManagement Console Mounting Hardware Installation Space Requirements Installing the ARNVerifying Site Requirements Positioning the ARN on a Flat Surface Determine how you want the ARN to fit in the equipment rack Rack-Mounting the ARN Options for Attaching Flange Brackets to Rack-Mount the ARN Installing the ARN in an Electronic Enclosure Rack ARN Module Locations Understanding the ARN Module Locations Connecting to an Ethernet Interface Connecting Communications Cables Cable must have a 15-position D-SUB receptacle Connecting to the AUI Connecting an Ethernet 10BASE-T Cable Connecting to the UTP Interface Connecting to the Fiber Interface Connecting to a Token Ring Interface Connecting a Token Ring STP Cable Connecting to the STP Interface 10. Connecting a Token Ring UTP Cable Connecting to a Serial Interface COM3 13. Connecting the Isdn BRI Cable Connecting to the Isdn Interface Connecting to the FT1/T1 DSU/CSU Interface Connecting to the 56/64K DSU/CSU Interface 15. Connecting the FT1/T1 DSU/CSU Cable Connecting to the E1/FE1 DSU/CSU Interface 17. Connecting a Telephone Cable Connecting to the Integrated V.34 Modem Front-Panel Modem Adapter Module Defaults Connecting to the X.25 PAD InterfaceModem Signal/Parameter Default Value 18. Connecting a Breakout Box to the X.25 PAD Interface To connect X.25 PAD services Connecting a PC Console Connecting a Management ConsoleBaud rate Data bits Stop bit No parity 19. Connecting the Console/Modem Cable 21. Connecting a PC Console to an ARN Connecting a Terminal Console Parameter Value Console Parameters Console Modem Defaults Connecting a Console Modem Connecting to an Integrated V.34 Console Modem Module Connecting an External Console Modem 24. Connecting to an Integrated Console Modem Connecting the Power Cable 25. Connecting the Power Cable to the ARN 26. Flash Memory Card Installing the Flash Memory Card For information about Go to Where to Go Next Topic Go to Understanding the Startup Process Router does not operate Summary of Initial Startup Options Interface Supported Not Supported Supported Boot Options by Interface Starting the ARN for the First Time Using EZ-Install Interrupting the Boot Process Using Netboot, Directed Netboot, or Local Boot ARN monitor login prompt appears Logging in to the Command Line SoftwareManager Getcfg Continuing with Netboot Starting the ARN Continuing with Directed Netboot To use the directed netboot feature Verifying Directed Netboot Configuration Bconfig config local Continuing with Local Boot the Quick-Start Procedure Quick-Start script begins running Technician Interface prompt $ appearsRun instarn.bat Where to Go Next Page Understanding the ARN LEDs Chapter Operating the ARN Describes the base module diagnostic LEDs Diagnostic LEDsBase Module Diagnostic LEDs Base Module LEDs Describes the base module Ethernet 10BASE-T LEDs Ethernet 10BASE-T LEDsBase Module Ethernet 10BASE-T LEDs Ethernet 100BASE-Fx LEDs Ethernet 10/100BASE-Tx LEDsToken Ring LEDs Ethernet LEDs Expansion Module LEDsDescribes the expansion module token ring LEDs Expansion Module Ethernet LEDs Serial LEDs Adapter Module LEDsDescribes the expansion module serial interface LEDs Serial LED 10 describes the Isdn adapter module LEDs Isdn BRI LEDs S/T or U Interfaces56/64K DSU/CSU LEDs 11 describes the 56/64K DSU/CSU adapter module LEDs PAD LEDs FT1/T1 and FE1/E1 DSU/CSU LEDs13 describes the X.25 PAD adapter module LEDs Modem LEDs Modem LEDs Ensuring a Successful Installation Boot Status Run LED Boot LED Boot Status LEDs ARN power switch is located on the back panel Figure Powering On and Off ARN Reset Button Resetting the ARN To remove a memory card from an ARN Removing a Flash Memory Card Protecting Memory Card Files Memory Card Read/Write Protect Switch Where to Go Next Page Preparing for Installation Installing a WAN Adapter Module Powering Down Downloading New Boot and Diagnostic CodeBefore installing a WAN adapter module Set the power switch to 0, off refer to -25 on Location of Adapter Module Slots 1 Removing the Filler Panel Removing the Filler Panel from Slot To remove a WAN adapter module Removing an Adapter Module To install a WAN adapter module Installing an Adapter Module Securing the Adapter Module to the Front Panel What to Do Next Topic 56 64 -fr -annexd -lmi -annexa-intclk Using the ifconfig Command Table A-1 COM Interface ifconfig Command Settings Table A-2. Ethernet Interface ifconfig Command Settings Configuring an Ethernet Interface for Network Booting Table A-3 Token Ring Interface ifconfig Command Settings Configuring a Token Ring Interface for Network Booting Examples of ifconfig Commands Enabling and Disabling Interfaces with ifconfig Format for the bconfig Command Using the bconfig CommandBconfig -d image config Bconfig image config local network TFTPhost TFTPpathname Examples of bconfig Commands Verifying Your ConfigurationBconfig image network bconfig config network Boot Options Page Appendix B Using Local Boot the Quick-Start Procedure Before You Run Quick-Start Understanding Quick-Start Connector Names and Numbers Filling Out the Worksheets Table B-1 Quick-Start Connector Names and NumbersModule Interface Base Expansion Adapter Fill out one Wide Area Protocol worksheet Global Information Worksheet Global Information WorksheetStep Requested Information Options Your Response COM1 COM2 COM3 COM4 COM5 Global Information Worksheet RIP Worksheet Router Protocol WorksheetsRequested Information Options Your Response RIP Worksheet Nbma Ospf Worksheet Static Route to Site Manager Worksheet Static Route to Site Manager Worksheet Wide Area Protocol WorksheetsNortel Networks Proprietary PPP Worksheet Nortel Networks Proprietary PPP Worksheet Chap PPP Standard Worksheet PPP Standard Worksheet Running the Quick-Start Script Technician Interface login prompt appearsSmds Worksheet Task Action Details Table B-2 Quick-Start CommandsPress Control-c Figure B-2. Starting the IP Interface Test To cancel the test, enter q Physical Specifications Appendix C ARN Technical Specifications Environmental Specifications Electrical SpecificationsTable C-1 ARN Wall Outlet Requirements Country Outlet Voltage Hardware Communications Options One V.34 modem interface One Isdn BRI U interfaceOne 56/64K DSU/CSU interface One FE1/E1 DSU/CSU interface Table C-2 Network Interfaces Available on ARNs Ethernet Attachment Unit Interface AUI Pin Assignment Pin No Signal NameTable C-3 AUI Pin Assignments Ethernet 10BASE-T and 10/100BASE-Tx Interfaces Pin Assignment Pin No Signal Function Table C-5. Token Ring STP Interface Pin Assignments Token Ring STP Interface Serial Interfaces Token Ring UTP InterfaceTable C-6. Token Ring UTP Interface Pin Assignments Table C-7 Serial Interface Pin Assignments Pin Assignment Pin No. Signal Name Isdn BRI U Interface Pin Assignment Pin No SignalTable C-8. Isdn BRI U Interface Pin Assignments Table C-9. Isdn BRI S/T Interface Pin Assignments Isdn BRI S/T Interface FT1/T1 DSU/CSU Connections 56/64K DSU/CSU InterfaceTable C-10 /64K DSU/CSU Interface Pin Assignments Table C-11 RJ-48C Connector Pinouts Table C-11 lists the ARN FT1/T1 DSU/CSU connector pinouts PAD Connections Signal Pin Assignment Pin No FunctionTable C-12 Breakout Box Interface Pin Assignments Local Console Connections RJ-11 Interface for V.34 ModemTable C-13. V.34 Interface Pin Assignments Pin Assignment Pin No Signal Name Direction Service Modem ConnectionsTable C-14. Local Console Port DB-9 Pin Assignments Table C-15. Service Modem Port DB-9 Pin Assignments Port Location Port Description Type of Circuit ARN Ethernet Base Model Safety Status ARN Token Ring Base Model Safety Status ARN 10/100BASE-T Ethernet Base Model Safety Status Synchronous Cabling Requirements ARN Expansion Modules Safety Status Local Wire Connections Nortel Networks Termination Remote Termination Pin Signal Pin 7 30 31 Pin 13 Pin 14 Rev Send Data a Table D-7 Interface Order No Table D-8 Interface Order No Table D-9 Interface Order No Figure D-5. Cable 7224 X.21 Compliant Pin 46 48 GRD Pin 38 Pin 14 Serial Adapter Module Requirements Table D-11 Safety Status Order No. CV0004001 Table D-12 Isdn BRI Safety Status Order No. CV0004002 Table D-13 lists the Isdn connector pinoutsTable D-13 Isdn Connector Pinouts Pin Signal Table D-14. Isdn BRI Power Requirements Power Requirements for Isdn BRI and Serial Adapter ModulesAmperage Clearance Creepage Y Host or expansion card Voltage used or generated by other parts Requirements for European Operation Page 10BASE-T Numbers Index-2 Index-3 Index-4 Index-5 Index-6 Index-7 Index-8