Safety Instructions | Nvidia 2 specs

NVIDIA Quadro G-Sync II User Guide

Safety Instructions

To reduce the risk of ﬁre, electric shock, and injury always follow basic safety precautions.

Note: All hardware must be installed prior to installation of the drivers.

Remove power from your computer by disconnecting the AC main source before cleaning. Do not use liquid or aerosol cleaners. Use a soft, damp cloth from cleaning exposed surfaces.

Do not operate this product near water or when your hands or body are wet.

Do not place this product on soft surfaces that could block the ventilation slots and cause overheating.

Do not place this product near a heating register or radiator.

Place this product securely on a stable surface. Serious damage to this product may result if it falls.

Do not allow anything to rest on the power cord. Do not place

this product where a person can step or trip on the power cord or telephone cords.

Do not disassemble this product. There are no user-serviceable parts inside.

Do not put lighted candles, cigarettes, cigars, and so forth, on this product.

Do not overload the AC main source and power extension cords. Doing so increases the risk of ﬁre and electric shock.

6

Image 13

Nvidia 2 manual Safety Instructions

Contents

176-0002-000 Page Page Nvidia Quadro G-Sync Page Table of Contents References and Resources About This Guide Introduction to Nvidia Quadro G-Sync Nvidia Quadro G-Sync II User Guide Implementing SLI Technology System Requirements Unpacking Nvidia Frame Synchronization Two 2 Ribbon Cables Nvidia Quadro G-Sync II Equipment Safety Instructions Installing Nvidia Quadro G-Sync II Card Quadro G-Sync Nvidia Frame Synchronization Under Windows XP Set Up the Hardware How To Set Up Genlock VID IA Q uadro G-Sync Onnector Bracket Sync Source Server Basic Genlock Setup Set Up the Software Click OK to save the settings Detecting the House Sync Signal Under The synchronization pulses are based on, click Using the House Sync Signal Ou tgo in g Sync trigg ered from lead in g and falling ed ge Restoring an Unstable Display How To Set Up Frame LockViewing the Connection Status Er ver Basic Server Setup Set Up the Server SoftwareClick Apply Click Edit Settings to open the Server Settings dialog box Changing the Timing Signal Frequency Basic Client Setup Set Up the Client Software Yn c D elay Skew Introducing a Timing Delay at Client Systems Swap Sync Setup Setting Up Genlock + Frame Lock Checking the Connection Status Swap Sync Nvidia Quadro G-Sync II User Guide Nvidia Frame Synchronization Under Linux Using the nvidia-settings Utility Nvidia Q uadro G-Sync Connector Bracket Syn c Sou rce An X Server is typically speciﬁed in the format systemm Go to the nvidia-settingsframe lock panel Synchronizing to the External House Signal Ou tgo in g Sync trigg ered from lead in g and falling ed ge Understanding the Status Indicators Sync and Connection Status for the Genlock Server Four frame locked systems An X Server is typically speciﬁed in the format systemm Test the Connections Sync and Connection Status for the Server Check the Use House Sync if Present check box Frame Lock Restrictions Leveraging Frame Lock Genlock in OpenGL ‰ Frame Lock + SLI SFR, AFR, or Sliaa Two Quadros, Single Supported Frame Lock Conﬁgurations Sample Conﬁgurations General Steps Query the enabled displays on the Quadro Make sure frame lock sync is disabledGenlock Example Check that the refresh rate is the one we want Conﬁgure the house sync signal video mode Enable use of the house sync signalEnable framelocking Toggle the test signal Frame Lock Example Disable frame lock‰ First display from system Disable the house sync signal on the master device Query the enabled displays on the QuadrosEnable frame lock on server Check the refresh rate is the same for all displays Make sure frame lock is disabled for all Quadros Enable frame lock on slave devices Verify that the refresh rate is the same for all displays Writing a Frame Lock NV-CONTROL Client Enable frame lock on the slave devicesWriting a Frame Lock Client for NV-CONTROL 1.8 and earlier Framelocksyncdisable on each X screen to disable frame lock Are using a house sync. Most likely, you wantNode Most likely, you want Writing a Frame Lock Client for NV-CONTROL 1.9 and later Conﬁguring the Frame Lock Group Querying the Frame Lock Capabilities of a SystemQuery the number of Quadro G-Sync II devices on Quadro G-Sync II device Most likely, you want Enable frame lock on each Quadro by setting Nvctrlframelock Using a house sync. Most likely, you wantEnabling/Disabling Frame Lock Nvidia Quadro G-Sync II User Guide Using the OpenGL Extensions About Buffer Swaps Frame Synchronization Using the OpenGL ExtensionsKey Points and Deﬁnitions Window Buffer Swaps Buffer Swap Criteria Frame Counter Conﬁguring for Swap SyncConﬁguring Swap Groups Conﬁguring Swap Barriers OpenGL Extensions‰ To bind a group to a barrier, call WglBindSwapBarrierNV GlxBindSwapBarrierNV WglJoinSwapGroupNV, glxJoinSwapGroupNVThis call binds a swap group to a barrier WglQueryMaxSwapGroupsNV GlxQueryMaxSwapGroupsNV WglQuerySwapGroupNV GlxQuerySwapGroupNV WglQueryFrameCountNV,glxQueryFrameCount WglResetFrameCountNV,glxResetFrameCount Getting Driver Updates Nvidia Quadro G-Sync II User Guide Registering Your Quadro Sync Registration, Support Warranty Warranty and Support Compliance and Certiﬁcations Copyright